RADIATOR > INSTALLATION |
| 1. INSTALL RADIATOR ASSEMBLY |
Install the radiator with the 4 bolts.
| 2. CONNECT NO. 1 OIL COOLER TUBE INLET (for Automatic Transmission) |
Connect the No. 1 oil cooler tube inlet to the radiator.
| 3. CONNECT NO. 1 OIL COOLER TUBE OUTLET (for Automatic Transmission) |
Connect the No. 1 oil cooler tube outlet to the radiator.
| 4. INSTALL FAN SHROUD |
Install the fan pulley to the engine water pump.
Install the fan shroud together with the fluid coupling with fan between the radiator and engine component.
Install the fluid coupling with fan to the fan pulley with the 4 nuts.
Tighten the nuts as much as possible by hand.
![]() |
Attach the claws of the fan shroud to the radiator.
Install the fan shroud with the 2 bolts.
Install the fan and generator V belt (Click here).
Tighten the 4 nuts of the fluid coupling with fan.
Install the radiator reservoir with the 2 bolts.
Connect the No. 1 and No. 2 water by-pass hoses to the radiator.
Install the oil reservoir with the 3 bolts.
| 5. CONNECT RADIATOR HOSE INLET |
Connect the radiator hose inlet to the radiator.
| 6. CONNECT RADIATOR HOSE OUTLET |
Connect the radiator hose outlet to the radiator.
| 7. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the B line of the radiator reservoir.
| Item | Specified Condition |
| for Automatic Transmission | 11.1 liters (11.7 US qts, 9.8 Imp. qts) |
| for Manual Transmission | 9.8 liters (10.4 US qts, 8.6 Imp. qts) |
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
Using a wrench, install the vent plug.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Press the radiator hose inlet and radiator hose outlet several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
After the coolant cools down, check that the coolant level is at the F line.
If the coolant level is below the F line, add TOYOTA SLLC to the F line.
| 8. INSPECT FOR COOLANT LEAK |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
| 9. INSTALL RADIATOR SIDE DEFLECTOR LH |
Install the radiator side deflector LH with the 2 clips and attach the claw.
| 10. INSTALL RADIATOR SIDE DEFLECTOR RH |
Install the radiator side deflector RH with the 2 clips and attach the claw.
| 11. INSTALL RADIATOR GRILLE |
Attach the 6 claws to install the radiator grille.
Install the 2 screws and 2 clips.
| 12. INSTALL NO. 1 ENGINE UNDER COVER |