CYLINDER HEAD GASKET > INSTALLATION |
| 1. INSTALL CYLINDER HEAD GASKET |
![]() |
Check the piston protrusions for each cylinder.
Clean the cylinder block with solvent.
Set the piston of the cylinder to be measured to slightly before TDC.
| *1 | Measuring Tip |
| *2 | Protrusion |
Place a dial indicator on the cylinder block, and position the measuring tip as shown in the illustration.
Set the dial indicator at 0 mm (0 in.)
Find where the piston head protrudes most by slowly turning the crankshaft clockwise and counterclockwise.
![]() |
Measure the piston protrusion of each cylinder at the 2 points shown in the illustration.
| *1 | Measuring Point |
For the piston protrusion value of each cylinder, use the average of the 2 measurements of each cylinder.
![]() |
Select a new cylinder head gasket.
| *1 | Cutout Mark |
| Mark | Specified Condition |
| A | 0.80 to 0.90 mm (0.0315 to 0.0354 in.) |
| B | 0.85 to 0.95 mm (0.0335 to 0.0374 in.) |
| C | 0.90 to 1.00 mm (0.0354 to 0.0394 in.) |
| D | 0.95 to 1.05 mm (0.0374 to 0.0413 in.) |
| E | 1.00 to 1.10 mm (0.0394 to 0.0433 in.) |
Select the largest piston protrusion value from the measurements made. Then select a new appropriate gasket according to the table below.
| Item | Specified Condition | ||||
| Piston protrusion | 0.005 to 0.054 mm (0.000197 to 0.00213 in.) | 0.055 to 0.104 mm (0.00217 to 0.00409 in.) | 0.105 to 0.154 mm (0.00413 to 0.00606 in.) | 0.155 to 0.204 mm (0.00610 to 0.00803 in.) | 0.205 to 0.255 mm (0.00807 to 0.0100 in.) |
| Gasket to be used | A | B | C | D | E |
![]() |
Place the cylinder head on the cylinder block.
![]() | Front |
| 2. INSTALL CYLINDER HEAD SUB-ASSEMBLY |
Place the cylinder head on the cylinder head gasket.
Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.
![]() |
Install and uniformly tighten the 18 cylinder head bolts and 18 washers in several passes in the sequence shown in the illustration.
| Item | Specified Condition |
| A | 110 mm (4.33 in.) |
| B | 167 mm (6.57 in.) |
![]() |
Mark the front of each cylinder head bolt with paint.
| *1 | Painted Mark |
| *a | Front |
Further tighten the cylinder head bolts by 90° in the sequence shown in the illustration above.
Finally, tighten the cylinder head bolts by an additional 90°.
Check that the painted mark are now facing rearward.
| 3. INSTALL VALVE LIFTER |
Install the valve lifters.
Check that each valve lifter rotates smoothly by hand.
| 4. INSTALL CAMSHAFT |
![]() |
Using the crankshaft pulley bolt, set the No. 1 cylinder to 90° BTDC/compression.
| *1 | Key |
![]() |
Install the camshaft.
Apply engine oil to the thrust portion of the camshaft.
Place the camshaft on the cylinder head with the key groove facing upward.
| *1 | Key Groove |
| *a | Upward |
![]() |
Align the timing marks (1-dot marks) of the camshaft drive and driven main gears and set the No. 2 camshaft in place.
Remove any old seal packing (FIPG material) from the camshaft bearing cap.
![]() |
Apply seal packing to the specified areas shown in the illustration.
| *1 | Seal Packing |
| *2 | Oil Passage |
![]() |
Install the 5 bearing caps to their proper locations.
![]() |
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
Install and uniformly tighten the 15 bearing cap bolts in several passes in the sequence shown in the illustration.
![]() |
Install a new camshaft oil seal.
Apply MP grease to the lip of a new oil seal.
Using SST and a hammer, tap in the oil seal until its surface is flush with the surfaces of the camshaft bearing cap and cylinder head.
| 5. INSTALL NO. 2 TIMING BELT COVER |
![]() |
Apply seal packing (FIPG) to the specified areas shown in the illustration.
| *1 | Seal Packing |
Clean the bolts and their holes.
Apply adhesive to 2 or 3 threads at the end of 4 bolts.
Install the No. 2 timing belt cover with the 4 bolts and nut.
| 6. INSTALL CAMSHAFT TIMING PULLEY |
![]() |
Install the camshaft timing pulley.
Fasten the bolt of the camshaft timing pulley by holding the camshaft with a wrench.
| 7. INSTALL TIMING BELT |
| 8. INSPECT AND ADJUST VALVE CLEARANCE |
| 9. INSTALL EXHAUST MANIFOLD |
Temporarily install a new gasket, the exhaust manifold, 8 new collars and the 8 plate washers to the cylinder head with 8 new nuts.
![]() |
Tighten the 8 nuts in the order shown in the illustration.
| 10. INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET |
Install the No. 1 compressor mounting bracket with the 4 bolts.
| 11. CONNECT COOLER COMPRESSOR ASSEMBLY |
Connect the cooler compressor with the 4 bolts.
| 12. INSTALL TURBOCHARGER SUB-ASSEMBLY |
| 13. INSTALL FAN SHROUD |
| 14. INSTALL COMMON RAIL ASSEMBLY |
| 15. INSTALL INJECTOR ASSEMBLY |
| 16. INSTALL GLOW PLUG ASSEMBLY |
| 17. INSTALL INTAKE MANIFOLD |
| 18. ADD ENGINE OIL |
Add new engine oil.
| Oil Grade | Oil Viscosity (SAE) |
| G-DLD1, API CF-4 or CF (You may also use API CE or CD) | - 5W-30 - 10W-30 - 15W-40 - 20W-50 |
| Item | Specified Condition |
| Drain and refill without oil filter change | 6.6 liters (7.0 US qts, 5.8 Imp. qts) |
| Drain and refill with oil filter change | 6.9 liters (7.3 US qts, 6.1 Imp. qts) |
| Dry fill | 7.4 liters (7.8 US qts, 6.5 Imp. qts) |
Install the oil filler cap.
| 19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 20. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the B line of the radiator reservoir.
| Item | Specified Condition |
| for Automatic Transmission | 11.1 liters (11.7 US qts, 9.8 Imp. qts) |
| for Manual Transmission | 9.8 liters (10.4 US qts, 8.6 Imp. qts) |
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
Using a wrench, install the vent plug.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Press the radiator hose inlet and radiator hose outlet several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
After the coolant cools down, check that the coolant level is at the F line.
If the coolant level is below the F line, add TOYOTA SLLC to the F line.
| 21. BLEED AIR FROM FUEL SYSTEM |
![]() |
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.
Check if the engine starts.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs (Click here).
Start the engine.*1
Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak.*2
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.

Enter the following menus: Powertrain / Engine / DTC.
Read Current DTCs.
Clear the DTCs (Click here).
Repeat steps *1 to *3.
Enter the following menus: Powertrain / Engine / DTC.
Read Current DTCs.
| 22. INSPECT FOR COOLANT LEAK |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
| 23. INSPECT FOR OIL LEAK |
Start the engine. Make sure that there are no oil leaks from the areas that were worked on.
| 24. INSPECT FOR FUEL LEAK |
Check that there are no leaks from any part of the fuel system when the engine is stopped. If there is fuel leakage, repair or replace parts as necessary.
Start the engine and check that there are no leaks from any part of the fuel system. If there is fuel leakage, repair or replace parts as necessary.
Disconnect the return hose from the common rail.
Start the engine and check for fuel leaks from the return pipe.
If there is fuel leakage, replace the common rail.
Connect the intelligent tester to the DLC3.
Start the engine and turn the intelligent tester main switch on.
Select the Fuel Leak test from the Active Test mode on the intelligent tester.
If the intelligent tester is not available, fully depress the accelerator pedal quickly. Increase the engine speed to the maximum and maintain that speed for 2 seconds. Repeat this operation several times.
Check that there are no leaks from any part of the fuel system.
Reconnect the return hose to the common rail.
| 25. INSPECT FOR EXHAUST GAS LEAK |
| 26. INSPECT ENGINE OIL LEVEL |
Warm up the engine, stop the engine and wait 5 minutes. The engine oil level should be between the dipstick low level mark and full level mark.
If low, check for leakage and add oil up to the full level mark.