CYLINDER BLOCK > INSPECTION |
| 1. INSPECT CYLINDER BLOCK OIL ORIFICE |
Check the oil orifice for damage or clogging.
If necessary, replace the cylinder block oil orifice.
| 2. INSPECT OIL CHECK VALVE SUB-ASSEMBLY |
![]() |
Push the ball of the oil check valve with a wooden stick to check if it is stuck.
| *1 | Ball |
![]() | Push |
| 3. INSPECT NO. 1 OIL NOZZLE SUB-ASSEMBLY |
Check the No. 1 oil nozzle for damage or clogging.
If necessary, replace the No. 1 oil nozzle sub-assembly.
| 4. CLEAN CYLINDER BLOCK SUB-ASSEMBLY |
Using a gasket scraper, remove all the gasket material from the top surface of the cylinder block.
Using a soft brush and solvent, thoroughly clean the cylinder block sub-assembly.
| 5. INSPECT CYLINDER BLOCK FOR WARPAGE |
![]() |
Using a precision straightedge and feeler gauge, measure the surface of the cylinder block that contacts the cylinder head for warpage.
Visually check the cylinders for vertical scratches.
If deep scratches are present, rebore all 4 cylinders. If necessary, replace the cylinder block.
| 6. INSPECT CYLINDER BORE |
![]() |
Inspect the cylinder bore diameter.
| *1 | Mark 1, 2 or 3 |
| *2 | No. 1 |
| *3 | No. 2 |
| *4 | No. 3 |
| *5 | No. 4 |
![]() ![]() |
Using a cylinder gauge, measure the cylinder bore diameter at positions A, B and C in the thrust and axial directions.
| Item | Specified Condition |
| STD Mark 1 | 92.00 to 92.01 mm (3.6220 to 3.6224 in.) |
| STD Mark 2 | 92.01 to 92.02 mm (3.6224 to 3.6228 in.) |
| STD Mark 3 | 92.02 to 92.03 mm (3.6228 to 3.6232 in.) |
| O/S 0.50 | 92.50 to 92.53 mm (3.6417 to 3.6429 in.) |
| Item | Specified Condition |
| STD | 92.23 mm (3.6311 in.) |
| O/S 0.50 | 92.73 mm (3.6508 in.) |
| *1 | Axial Direction |
| *2 | Thrust Direction |
| *3 | Center |
![]() | Front |
| *1 | Ridge Reamer |
| 7. CLEAN PISTON |
Using a groove cleaning tool or broken ring, clean the piston ring grooves.
Using solvent and a brush, thoroughly clean the piston.
| 8. INSPECT PISTON DIAMETER |
![]() |
Using a micrometer, measure the piston diameter according to the following conditions: 1) measure at a right angle to the piston center line, and 2) measure at the indicated distance from the piston head.
| Item | Specified Condition |
| STD Mark 1 | 91.92 to 91.93 mm (3.6189 to 3.6193 in.) |
| STD Mark 2 | 91.93 to 91.94 mm (3.6193 to 3.6197 in.) |
| STD Mark 3 | 91.94 to 91.95 mm (3.6197 to 3.6201 in.) |
| O/S 0.50 | 92.42 to 92.45 mm (3.6386 to 3.6398 in.) |
| Item | Specified Condition |
| Mark A | 33.998 to 34.002 mm (1.3385 to 1.3387 in.) |
| Mark B | 34.002 to 34.006 mm (1.3387 to 1.3388 in.) |
| Mark C | 34.006 to 34.010 mm (1.3388 to 1.3390 in.) |
| *1 | Size Mark |
| *2 | Piston Pin Hole Inside Diameter Mark |
| *3 | Front Mark (Arrow) |
| *4 | Distance |
![]() |
Using a micrometer, measure the piston pin diameter.
| Item | Specified Condition |
| Mark A | 33.996 to 34.000 mm (1.3384 to 1.3386 in.) |
| Mark B | 34.000 to 34.004 mm (1.3386 to 1.3387 in.) |
| Mark C | 34.004 to 34.008 mm (1.3387 to 1.3389 in.) |
Subtract the piston pin diameter measurement from the piston pin hole inside diameter measurement.
![]() |
Inspect the piston pin fit.
At 80°C (176°F), check that the piston pin can be pushed into the piston pin hole with your thumb.
If the pin can be installed at a lower temperature, replace the piston with pin sub-assembly.
| 9. INSPECT PISTON OIL CLEARANCE |
![]() |
Measure the cylinder bore diameter in the thrust direction.
| *1 | No. 1 |
| *2 | No. 2 |
| *3 | No. 3 |
| *4 | No. 4 |
| *5 | Mark 1, 2 or 3 |
| *6 | Size Mark |
Subtract the piston diameter measurement from the cylinder bore diameter measurement.
| 10. INSPECT RING GROOVE CLEARANCE |
Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.
| Item | Specified Condition |
| No. 1 piston ring | 0.060 to 0.100 mm (0.00236 to 0.00394 in.) |
| No. 2 piston ring | 0.050 to 0.095 mm (0.00197 to 0.00374 in.) |
| Oil ring | 0.030 to 0.075 mm (0.00118 to 0.00295 in.) |
| 11. INSPECT PISTON RING END GAP |
Insert the piston ring into the cylinder bore.
Using a piston, push the piston ring a little beyond the bottom of the ring travel, 120 mm (4.72 in.) from the top of the cylinder block.
Using a feeler gauge, measure the end gap.
| Item | Specified Condition |
| No. 1 piston ring | 0.27 to 0.39 mm (0.0106 to 0.0154 in.) |
| No. 2 piston ring | 0.47 to 0.62 mm (0.0185 to 0.0244 in.) |
| Oil ring | 0.20 to 0.40 mm (0.00787 to 0.0157 in.) |
| Item | Specified Condition |
| No. 1 piston ring | 1.21 mm (0.0476 in.) |
| No. 2 piston ring | 1.44 mm (0.0567 in.) |
| Oil ring | 1.22 mm (0.0480 in.) |
| 12. INSPECT PISTON PIN OIL CLEARANCE |
![]() |
Using a caliper gauge, measure the inside diameter of the connecting rod bush.
| Item | Specified Condition |
| Mark A | 34.012 to 34.016 mm (1.3390 to 1.3392 in.) |
| Mark B | 34.016 to 34.020 mm (1.3392 to 1.3393 in.) |
| Mark C | 34.020 to 34.024 mm (1.3393 to 1.3395 in.) |
| *1 | Connecting Rod Bush Inside Diameter Mark A, B or C |
| *2 | Front Mark |
Subtract the piston pin diameter measurement from the bush inside diameter measurement.
| 13. INSPECT CONNECTING ROD SUB-ASSEMBLY |
Using a rod aligner and feeler gauge, check the connecting rod alignment.
![]() |
Check if the connecting rod is bent.
![]() |
Check if the connecting rod is twisted.
| 14. INSPECT CONNECTING ROD BOLT |
![]() |
Using a vernier caliper, measure the diameter of the tension portion of the bolt.
| *1 | Tension Portion |
| 15. INSPECT CRANKSHAFT |
Inspect for circle runout.
Place the crankshaft on V-blocks.
Using a dial indicator, measure the circle runout at the center journal.
![]() |
Inspect the main journals and crank pins.
Using a micrometer, measure the diameter of each main journal and crank pin.
| Item | Specified Condition |
| Mark 1 | 69.994 to 70.000 mm (2.7557 to 2.7559 in.) |
| Mark 2 | 69.988 to 69.994 mm (2.7554 to 2.7557 in.) |
| Mark 3 | 69.982 to 69.988 mm (2.7552 to 2.7554 in.) |
| U/S 0.25 | 69.745 to 69.755 mm (2.7459 to 2.7463 in.) |
| U/S 0.50 | 69.495 to 69.505 mm (2.7360 to 2.7364 in.) |
| Item | Specified Condition |
| Mark 1 | 58.994 to 59.000 mm (2.3226 to 2.3228 in.) |
| Mark 2 | 58.988 to 58.994 mm (2.3224 to 2.3226 in.) |
| Mark 3 | 58.982 to 58.988 mm (2.3221 to 2.3224 in.) |
Check each main journal and crank pin for taper and out-of-round as shown in the illustration.
If necessary, grind and hone the main journals and/or crank pins.
Grind and hone the main journals and/or crank pins to the finished undersized diameter (refer to the procedures above).
Install new main journal and/or crank pin undersized bearings.
| 16. INSPECT CRANKSHAFT BEARING CAP SET BOLT |
![]() |
Using a vernier caliper, measure the diameter of the crankshaft bearing cap set bolt in the measuring area.
| *1 | Measuring Area |