ENGINE UNIT > DISASSEMBLY |
| 1. REMOVE OIL FILLER CAP SUB-ASSEMBLY |
| 2. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Using a small screwdriver, remove the nozzle holder seal by prying between the nozzle holder seal and the cutout part of the cylinder head cover.
Disconnect the ventilation hose.
![]() |
Remove the 10 bolts, 2 nuts, cylinder head cover and cylinder head cover gasket.
![]() |
Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.
| 3. REMOVE INJECTOR ASSEMBLY |
![]() |
Remove the union bolt, 4 injector hollow screws, 5 gaskets and nozzle leakage pipe.
| *1 | Union Bolt |
![]() |
Remove the 4 bolts, 4 washers, 4 No. 1 nozzle holder clamps and 4 injectors.
Remove the O-ring from each injector.
Remove the 4 injection nozzle seats from the cylinder head.
| 4. REMOVE CAMSHAFT TIMING PULLEY |
![]() |
Remove the bolt of the camshaft timing pulley while holding the camshaft with a wrench.
Remove the camshaft timing pulley.
| 5. REMOVE NO. 2 TIMING BELT COVER |
Remove the 4 bolts, nut and No. 2 timing belt cover.
| 6. REMOVE CYLINDER BLOCK INSULATOR |
![]() |
Remove the cylinder block insulator from the cylinder head.
| 7. REMOVE CAMSHAFT |
![]() |
Turn the camshaft with a wrench so that the key groove of the camshaft faces upward.
| *1 | Key Groove |
![]() |
Uniformly loosen the 15 bearing cap bolts in several passes in the sequence shown in the illustration.
Remove the 15 bearing cap bolts, 5 bearing caps, oil seal and 2 camshafts.
| 8. REMOVE VALVE LIFTER |
Remove the valve lifters.
| 9. REMOVE CYLINDER HEAD SUB-ASSEMBLY |
![]() |
Uniformly loosen the 18 cylinder head bolts in several passes in the sequence shown in the illustration. Then remove the 18 cylinder head bolts and 18 washers.
Remove the cylinder head from the dowels on the cylinder block and place the cylinder head on wooden blocks on a workbench.
| 10. REMOVE CYLINDER HEAD GASKET |
| 11. REMOVE ENGINE WATER PUMP ASSEMBLY |
![]() |
Remove the 5 bolts, 2 nuts, engine water pump and gasket.
| 12. REMOVE TIMING GEAR COVER |
![]() |
Remove the 14 bolts and 2 nuts.
![]() |
Pry the timing gear cover at the locations shown in the illustration and remove the timing gear cover.
![]() |
Remove the O-ring from the timing gear case.
| 13. REMOVE INJECTION GEAR |
![]() |
Secure the No. 2 idle sub gear to the No. 1 idle gear with a service bolt.
![]() |
Remove the injection gear.
| 14. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE |
![]() |
Remove the No. 1 crankshaft position sensor plate.
| 15. INSPECT BACKLASH OF CRANKSHAFT TIMING GEAR TO OIL PUMP GEAR |
![]() |
Using a dial indicator, measure the backlash.
| 16. INSPECT BACKLASH OF CRANKSHAFT TIMING GEAR TO NO. 1 IDLE GEAR |
![]() |
Using a dial indicator, measure the backlash.
| 17. INSPECT NO. 1 IDLE GEAR THRUST CLEARANCE |
Install the timing gear case, No. 1 idle gear and camshaft timing gear.
![]() |
Using a dial indicator, measure the thrust clearance.
| 18. REMOVE CRANKSHAFT TIMING GEAR |
![]() |
Using SST, remove the crankshaft timing gear.
| 19. INSPECT BACKLASH OF INJECTION GEAR TO NO. 1 IDLE GEAR |
Install the fuel supply pump with the 2 nuts.
![]() |
Using SST, install the injection gear with the nut.
![]() |
Using a dial indicator, measure the backlash.
| 20. REMOVE IDLE GEAR THRUST PLATE |
![]() |
Remove the 2 bolts and idle gear thrust plate.
| 21. REMOVE NO. 1 IDLE GEAR |
![]() |
Remove the No. 1 idle gear together with the No. 2 idle sub gear.
| 22. REMOVE NO. 1 IDLE GEAR SHAFT |
![]() |
Remove the No. 1 idle gear shaft.
| 23. INSPECT BACKLASH OF NO. 1 BALANCESHAFT TO OIL PUMP GEAR |
![]() |
Using a dial indicator, measure the backlash.
| 24. INSPECT BACKLASH OF NO. 2 BALANCESHAFT TO INJECTION GEAR |
![]() |
Using a dial indicator, measure the backlash.
![]() |
Using SST, remove the nut and injection gear.
Remove the 2 nuts and fuel supply pump.
Remove the gears and timing gear case.
| 25. REMOVE NO. 1 IDLE SUB GEAR |
![]() |
Mount the No. 1 idle gear and No. 2 idle sub gear in a vise.
![]() |
Using SST, turn the No. 1 idle sub gear clockwise and remove the service bolt.
| *1 | Service Bolt |
![]() |
Using snap ring pliers, remove the shaft snap ring.
![]() |
Remove the wave washer, No. 1 idle sub gear and idle gear spring.
| *1 | Wave Washer |
| *2 | No. 1 Idle Sub Gear |
| *3 | Idle Gear Spring |
| 26. REMOVE NO. 2 IDLE SUB GEAR |
![]() |
Turn the No. 1 idle gear over and set it in a vise.
![]() |
Using snap ring pliers, remove the shaft snap ring.
![]() |
Remove the wave washer, No. 2 idle sub gear and idle gear spring.
| *1 | Wave Washer |
| *2 | No. 2 Idle Sub Gear |
| *3 | Idle Gear Spring |
| 27. REMOVE OIL PAN SUB-ASSEMBLY |
Remove the 22 bolts and 2 nuts.
![]() |
Insert the blade of an oil pan seal cutter between the oil pan and cylinder block, cut through the applied sealer and remove the oil pan.
| 28. REMOVE OIL STRAINER SUB-ASSEMBLY |
Remove the 2 bolts, 2 nuts, oil strainer and gasket.
| 29. REMOVE TIMING GEAR CASE ASSEMBLY |
![]() |
Remove the union bolt and 8 bolts.
![]() |
Pry the timing gear case at the location shown in the illustration and remove the gear case and gasket.
![]() |
Remove the 2 O-rings.
| 30. INSPECT NO. 1 BALANCESHAFT THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while moving the No. 1 balanceshaft back and forth.
| 31. REMOVE NO. 1 BALANCESHAFT SUB-ASSEMBLY |
![]() |
Remove the 2 bolts and balanceshaft.
| 32. REMOVE NO. 1 BALANCESHAFT DRIVEN GEAR |
![]() |
Mount the balanceshaft between aluminum plates in a vise.
Remove the bolt, balanceshaft driven gear and balanceshaft thrust washer.
| 33. INSPECT NO. 2 BALANCESHAFT THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while moving the No. 2 balanceshaft back and forth.
| 34. REMOVE NO. 2 BALANCESHAFT SUB-ASSEMBLY |
![]() |
Remove the 2 bolts and balanceshaft.
| 35. REMOVE NO. 2 BALANCESHAFT DRIVEN GEAR |
![]() |
Mount the balanceshaft between aluminum plates in a vise.
Remove the bolt, balanceshaft driven gear and balanceshaft thrust washer.
| 36. REMOVE REAR ENGINE OIL SEAL RETAINER |
![]() |
Remove the 5 bolts.
Using a screwdriver, remove the rear engine oil seal retainer by prying between the rear engine oil seal retainer and cylinder block.
| 37. REMOVE FRONT CRANKSHAFT OIL SEAL |
![]() |
Using a screwdriver and hammer, tap out the oil seal.
| 38. REMOVE SUPPLY PUMP OIL SEAL |
![]() |
Using a screwdriver and hammer, tap out the oil seal.
| 39. REMOVE REAR CRANKSHAFT OIL SEAL |
![]() |
Using a screwdriver and hammer, tap out the oil seal.
| 40. REMOVE CYLINDER BLOCK OIL ORIFICE |
| 41. INSPECT CONNECTING ROD THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.
| 42. INSPECT CONNECTING ROD OIL CLEARANCE |
![]() |
Check the matchmarks on the connecting rod and cap to ensure correct reassembly.
| *1 | Matchmark |
Remove the 2 connecting rod cap bolts.
![]() |
Using the 2 removed connecting rod bolts, move the connecting rod cap back and forth to remove the connecting rod cap.
Remove the lower bearing from the connecting rod cap.
Clean the crank pin and bearings.
Check the crank pin and bearings for pitting and scratches.
If the crank pin or a bearing is damaged, replace the bearings. If necessary, grind or replace the crankshaft.
![]() |
Lay a strip of Plastigage across the crank pin.
| *1 | Plastigage |
![]() |
Install the connecting rod cap .
| *1 | Matchmark |
Remove the 2 bolts, connecting rod cap and lower bearing.
![]() ![]() |
Measure the Plastigage at its widest point.
| Item | Specified Condition |
| STD | 0.036 to 0.054 mm (0.00142 to 0.00212 in.) |
| U/S 0.25, U/S 0.50 | 0.037 to 0.077 mm (0.00146 to 0.00303 in.) |
| *1 | Plastigage |
| Item | Number Mark | ||||||||||
| Connecting rod cap | 1 | 2 | 3 | ||||||||
| Crankshaft | 1 | 2 | 3 | 1 | 2 | 3 | 1 | 2 | 3 | ||
| Bearing to be used | 2 | 3 | 4 | 3 | 4 | 5 | 4 | 5 | 6 | ||
| *1 | Mark 1, 2 or 3 |
| *2 | Mark 2, 3 or 4 |
| *3 | No. 1 |
| *4 | No. 2 |
| *5 | No. 3 |
| *6 | No. 4 |
| Item | Specified Condition |
| Mark 1 | 62.014 to 62.020 mm (2.4415 to 2.4417 in.) |
| Mark 2 | 62.020 to 62.026 mm (2.4417 to 2.4420 in.) |
| Mark 3 | 62.026 to 62.032 mm (2.4420 to 2.4422 in.) |
| Item | Specified Condition |
| Mark 1 | 58.994 to 59.000 mm (2.3226 to 2.3228 in.) |
| Mark 2 | 58.988 to 58.994 mm (2.3224 to 2.3226 in.) |
| Mark 3 | 58.982 to 58.988 mm (2.3221 to 2.3224 in.) |
| Item | Specified Condition |
| Mark 2 | 1.486 to 1.489 mm (0.0585 to 0.0586 in.) |
| Mark 3 | 1.489 to 1.492 mm (0.0586 to 0.0587 in.) |
| Mark 4 | 1.492 to 1.495 mm (0.0587 to 0.0589 in.) |
| Mark 5 | 1.495 to 1.498 mm (0.0589 to 0.0590 in.) |
| Mark 6 | 1.498 to 1.501 mm (0.0590 to 0.0591 in.) |
Completely remove the Plastigage.
| 43. REMOVE PISTON AND CONNECTING ROD |
![]() |
Using a ridge reamer, remove all the carbon from the top of the cylinder.
| *1 | Ridge Reamer |
Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block to remove them.
Remove the upper bearing from the connecting rod.
| 44. REMOVE CONNECTING ROD BEARING SET |
Remove the connecting rod bearings from the connecting rods and connecting rod caps.
| 45. REMOVE PISTON RING SET |
![]() |
Using a piston ring expander, remove the 2 piston rings.
Remove the coil and oil ring by hand.
| 46. REMOVE PISTON WITH PIN SUB-ASSEMBLY |
![]() |
Using a small screwdriver, pry out the 2 snap rings from the piston.
Gradually heat the piston to approximately 80°C (176°F).
![]() |
Using a plastic-faced hammer and brass bar, lightly tap out the piston pin. Then remove the connecting rod.
| 47. INSPECT CRANKSHAFT THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.
| Item | Specified Condition |
| STD | 2.430 to 2.480 mm (0.0957 to 0.0976 in.) |
| O/S 0.125 | 2.555 to 2.605 mm (0.1006 to 0.1026 in.) |
| O/S 0.250 | 2.680 to 2.730 mm (0.1055 to 0.1074 in.) |
| 48. INSPECT CRANKSHAFT OIL CLEARANCE |
![]() |
Uniformly loosen and remove the 10 crankshaft bearing cap bolts in several passes in the sequence shown in the illustration.
![]() |
Using the removed crankshaft bearing cap bolts, pry the cap back and forth and remove the crankshaft bearing caps, lower crankshaft bearings and lower thrust washers (No. 5 crankshaft bearing cap only).
Lift out the crankshaft.
Clean each main journal and bearing.
Check each crankshaft journal and bearing for pitting and scratches.
If a journal or one of its bearings is damaged, replace the bearings for that journal. If necessary, grind or replace the crankshaft.
Place the crankshaft on the cylinder block.
![]() |
Lay a strip of Plastigage across each journal.
| *1 | Plastigage |
Install the crankshaft bearing caps .
Remove the crankshaft bearing caps.
![]() ![]() |
Measure the Plastigage at its widest point.
| Item | Specified Condition |
| STD | 0.030 to 0.048 mm (0.00118 to 0.00189 in.) |
| O/S 0.25, O/S 0.50 | 0.037 to 0.077 mm (0.00146 to 0.00303 in.) |
| *1 | Plastigage |
| Item | Number Mark | ||||||||||
| Cylinder block | 1 | 2 | 3 | ||||||||
| Crankshaft | 1 | 2 | 3 | 1 | 2 | 3 | 1 | 2 | 3 | ||
| Bearing to be used | 2 | 3 | 4 | 3 | 4 | 5 | 4 | 5 | 6 | ||
| *1 | Mark 2, 3, 4, 5 or 6 |
| *2 | No. 1 |
| *3 | No. 2 |
| *4 | No. 3 |
| *5 | No. 4 |
| *6 | No. 5 |
| *a | Front |
| Item | Specified Condition |
| Mark 1 | 75.000 to 75.006 mm (2.9528 to 2.9530 in.) |
| Mark 2 | 75.006 to 75.012 mm (2.9530 to 2.9532 in.) |
| Mark 3 | 75.012 to 75. 018 mm (2.9532 to 2.9535 in.) |
| Item | Specified Condition |
| Mark 1 | 69.994 to 70.000 mm (2.7557 to 2.7559 in.) |
| Mark 2 | 69.988 to 69.994 mm (2.7554 to 2.7557 in.) |
| Mark 3 | 69.982 to 69.988 mm (2.7552 to 2.7554 in.) |
| Item | Specified Condition |
| Mark 2 | 2.482 to 2.485 mm (0.0977 to 0.0978 in.) |
| Mark 3 | 2.485 to 2.488 mm (0.0978 to 0.0980 in.) |
| Mark 4 | 2.488 to 2.491 mm (0.0980 to 0.0981 in.) |
| Mark 5 | 2.491 to 2.494 mm (0.0981 to 0.0982 in.) |
| Mark 6 | 2.494 to 2.497 mm (0.0982 to 0.0983 in.) |
Completely remove the Plastigage.
| 49. REMOVE CRANKSHAFT |
Lift out the crankshaft.
Remove the upper bearings and upper thrust washers (No. 5 crankshaft bearing only) from the cylinder block.
| 50. REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY |
Remove the 4 check valves and 4 oil nozzles.
| 51. REMOVE STUD BOLT |
Remove the stud bolts.