CYLINDER BLOCK > DISASSEMBLY |
| 1. REMOVE CYLINDER BLOCK OIL ORIFICE |
| 2. INSPECT CONNECTING ROD THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.
| 3. INSPECT CONNECTING ROD OIL CLEARANCE |
![]() |
Check the matchmarks on the connecting rod and cap to ensure correct reassembly.
| *1 | Matchmark |
Remove the 2 connecting rod cap bolts.
![]() |
Using the 2 removed connecting rod bolts, move the connecting rod cap back and forth to remove the connecting rod cap.
Remove the lower bearing from the connecting rod cap.
Clean the crank pin and bearings.
Check the crank pin and bearings for pitting and scratches.
If the crank pin or a bearing is damaged, replace the bearings. If necessary, grind or replace the crankshaft.
![]() |
Lay a strip of Plastigage across the crank pin.
| *1 | Plastigage |
Install the connecting rod cap .
Remove the 2 bolts, connecting rod cap and lower bearing.
![]() ![]() |
Measure the Plastigage at its widest point.
| Item | Specified Condition |
| STD | 0.036 to 0.054 mm (0.00142 to 0.00212 in.) |
| U/S 0.25, U/S 0.50 | 0.037 to 0.077 mm (0.00146 to 0.00303 in.) |
| *1 | Plastigage |
| Item | Number Mark | ||||||||||
| Connecting rod cap | 1 | 2 | 3 | ||||||||
| Crankshaft | 1 | 2 | 3 | 1 | 2 | 3 | 1 | 2 | 3 | ||
| Bearing to be used | 2 | 3 | 4 | 3 | 4 | 5 | 4 | 5 | 6 | ||
| *1 | Mark 1, 2 or 3 |
| *2 | Mark 2, 3 or 4 |
| *3 | No. 1 |
| *4 | No. 2 |
| *5 | No. 3 |
| *6 | No. 4 |
| Item | Specified Condition |
| Mark 1 | 62.014 to 62.020 mm (2.4415 to 2.4417 in.) |
| Mark 2 | 62.020 to 62.026 mm (2.4417 to 2.4420 in.) |
| Mark 3 | 62.026 to 62.032 mm (2.4420 to 2.4422 in.) |
| Item | Specified Condition |
| Mark 1 | 58.994 to 59.000 mm (2.3226 to 2.3228 in.) |
| Mark 2 | 58.988 to 58.994 mm (2.3224 to 2.3226 in.) |
| Mark 3 | 58.982 to 58.988 mm (2.3221 to 2.3224 in.) |
| Item | Specified Condition |
| Mark 2 | 1.486 to 1.489 mm (0.0585 to 0.0586 in.) |
| Mark 3 | 1.489 to 1.492 mm (0.0586 to 0.0587 in.) |
| Mark 4 | 1.492 to 1.495 mm (0.0587 to 0.0589 in.) |
| Mark 5 | 1.495 to 1.498 mm (0.0589 to 0.0590 in.) |
| Mark 6 | 1.498 to 1.501 mm (0.0590 to 0.0591 in.) |
Completely remove the Plastigage.
| 4. REMOVE PISTON AND CONNECTING ROD |
![]() |
Using a ridge reamer, remove all the carbon from the top of the cylinder.
| *1 | Ridge Reamer |
Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block to remove them.
Remove the upper bearing from the connecting rod.
| 5. REMOVE CONNECTING ROD BEARING |
Remove the connecting rod bearings from the connecting rods and connecting rod caps.
| 6. REMOVE PISTON RING SET |
![]() |
Using a piston ring expander, remove the 2 piston rings.
Remove the coil and oil ring by hand.
| 7. REMOVE PISTON WITH PIN SUB-ASSEMBLY |
![]() |
Using a small screwdriver, pry out the 2 snap rings from the piston.
Gradually heat the piston to approximately 80°C (176°F).
![]() |
Using a plastic-faced hammer and brass bar, lightly tap out the piston pin. Then remove the connecting rod.
| 8. INSPECT CRANKSHAFT THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.
| Item | Specified Condition |
| STD | 2.430 to 2.480 mm (0.0957 to 0.0976 in.) |
| O/S 0.125 | 2.555 to 2.605 mm (0.1005 to 0.1025 in.) |
| O/S 0.250 | 2.680 to 2.730 mm (0.1055 to 0.1074 in.) |
| 9. INSPECT CRANKSHAFT OIL CLEARANCE |
![]() |
Uniformly loosen and remove the 10 crankshaft bearing cap bolts in several passes in the sequence shown in the illustration.
![]() |
Using the removed crankshaft bearing cap bolts, pry the cap back and forth and remove the crankshaft bearing caps, lower crankshaft bearings and lower thrust washers (No. 5 crankshaft bearing cap only).
Lift out the crankshaft.
Clean each main journal and bearing.
Check each crankshaft journal and bearing for pitting and scratches.
If a journal or one of its bearings is damaged, replace the bearings for that journal. If necessary, grind or replace the crankshaft.
Place the crankshaft on the cylinder block.
![]() |
Lay a strip of Plastigage across each journal.
| *1 | Plastigage |
Install the crankshaft bearing caps .
Remove the crankshaft bearing caps.
![]() ![]() |
Measure the Plastigage at its widest point.
| Item | Specified Condition |
| STD | 0.030 to 0.048 mm (0.00118 to 0.00189 in.) |
| U/S 0.25, U/S 0.50 | 0.037 to 0.077 mm (0.00146 to 0.00303 in.) |
| *1 | Plastigage |
| Item | Number Mark | ||||||||||
| Cylinder block | 1 | 2 | 3 | ||||||||
| Crankshaft | 1 | 2 | 3 | 1 | 2 | 3 | 1 | 2 | 3 | ||
| Bearing to be used | 2 | 3 | 4 | 3 | 4 | 5 | 4 | 5 | 6 | ||
| *1 | Mark 2, 3, 4, 5 or 6 |
| *2 | No. 1 |
| *3 | No. 2 |
| *4 | No. 3 |
| *5 | No. 4 |
| *6 | No. 5 |
| *a | Front |
| Item | Specified Condition |
| Mark 1 | 75.000 to 75.006 mm (2.9528 to 2.9530 in.) |
| Mark 2 | 75.006 to 75.012 mm (2.9530 to 2.9532 in.) |
| Mark 3 | 75.012 to 75. 018 mm (2.9532 to 2.9535 in.) |
| Item | Specified Condition |
| Mark 1 | 69.994 to 70.000 mm (2.7557 to 2.7559 in.) |
| Mark 2 | 69.988 to 69.994 mm (2.7554 to 2.7557 in.) |
| Mark 3 | 69.982 to 69.988 mm (2.7552 to 2.7554 in.) |
| Item | Specified Condition |
| Mark 2 | 2.482 to 2.485 mm (0.0977 to 0.0978 in.) |
| Mark 3 | 2.485 to 2.488 mm (0.0978 to 0.0980 in.) |
| Mark 4 | 2.488 to 2.491 mm (0.0980 to 0.0981 in.) |
| Mark 5 | 2.491 to 2.494 mm (0.0981 to 0.0982 in.) |
| Mark 6 | 2.494 to 2.497 mm (0.0982 to 0.0983 in.) |
Completely remove the Plastigage.
| 10. REMOVE CRANKSHAFT |
Lift out the crankshaft.
Remove the upper bearings and upper thrust washers (No. 5 crankshaft bearing only) from the cylinder block.
| 11. REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY |
Remove the 4 check valves and 4 oil nozzles.
| 12. REMOVE STUD BOLT |
Remove the stud bolts.