OIL PUMP (w/ Glow Plug Controller) > INSTALLATION |
| 1. INSTALL TIMING GEAR CASE ASSEMBLY |
![]() |
Install 2 new O-rings to the cylinder block.
| *1 | New O-Ring |
![]() |
Install a new gasket to the groove of the timing gear case.
| *1 | New Gasket |
Remove any old seal packing (FIPG material).
![]() |
Apply seal packing to the timing gear case as shown in the illustration.
| *1 | Seal Packing |
![]() |
Align the "2" marks of the No. 1 balanceshaft driven gear and oil pump drive gear.
Install the timing gear case with the union bolt and 8 bolts.
| 2. INSTALL OIL STRAINER SUB-ASSEMBLY |
Install a new gasket and the oil strainer with the 2 bolts and 2 nuts.
| 3. INSTALL OIL PAN SUB-ASSEMBLY |
![]() |
Remove any old seal packing (FIPG material).
Apply seal packing to the oil pan as shown in the illustration.
Install the oil pan with the 22 bolts and 2 nuts.
| 4. INSTALL INJECTION GEAR |
Install a new O-ring and the fuel supply pump with the 2 nuts.
Temporarily install the injection gear with the nut.
![]() |
Align the "3" marks of the No. 2 balanceshaft driven gear and injection gear.
![]() |
Install a new O-ring to the injection gear.
| *1 | New O-Ring |
![]() |
Install the injection gear set nut.
Using SST, tighten the set nut.
| 5. INSTALL CRANKSHAFT TIMING GEAR |
![]() |
Position the crankshaft timing gear with the "1" timing marks facing forward.
Align the key groove of the crankshaft timing gear with the set key on the crankshaft.
Using SST and a hammer, tap on the timing gear to install it.
| 6. INSTALL NO. 1 IDLE GEAR SHAFT |
![]() |
Apply a coat of engine oil to the No. 1 idle gear shaft.
| *1 | Engine Oil |
![]() |
Install the gear shaft as shown in the illustration.
| *1 | Oil Hole |
| 7. INSTALL NO. 1 IDLE GEAR |
![]() |
Align the "4" and "5" timing marks of the idle gear and crankshaft timing gear.
| *a | Turn |
Using SST, turn the injection gear and align the "4" timing marks of the idle gear and injection gear, and then mesh the gears.
![]() |
Position the idle gear thrust plate with the protrusion facing forward.
| *1 | Service Bolt |
Align the bolt holes and install the idle gear thrust plate with the 2 bolts.
Remove the service bolt.
| 8. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE |
Align the key groove of the No. 1 crankshaft position sensor plate with the set key.
Install the No. 1 crankshaft position sensor plate with the cupped side facing outward.
| 9. INSTALL TIMING GEAR COVER |
Remove any old seal packing (FIPG material).
![]() |
Apply seal packing to the timing gear cover as shown in the illustration.
| *1 | Seal Packing |
Install a new O-ring to the timing gear case.
Install the timing gear cover with the 14 bolts and 2 nuts.
![]() |
Remove the screw plug and gasket.
Pour approximately 50 cc (3.05 cu. in.) of engine oil into the oil pump.
Install a new gasket and the screw plug.
Install the No. 1 vacuum transmitting pipe with the bolt.
| 10. INSTALL CRANKSHAFT PULLEY |
Align the keyway of the pulley with the key located on the crankshaft, and then slide the pulley into place to install it.
![]() |
Using SST, install the pulley bolt.
| 11. INSTALL PUMP DRIVE SHAFT PULLEY |
Install a new O-ring to the fuel supply pump.
Temporarily install the fuel supply pump with the nut.
![]() |
Using SST, hold the crankshaft pulley and tighten the nut.
![]() |
Install the No. 2 camshaft timing pulley flange and pump drive shaft pulley with the 4 bolts.
![]() |
Using a dial indicator, check the thrust clearance of the pump drive shaft while moving the pump drive shaft pulley back and forth.
| 12. INSTALL CRANKSHAFT POSITION SENSOR |
Apply a light coat of engine oil to the O-ring of the crankshaft position sensor.
Install the crankshaft position sensor with the bolt.
Attach the 3 clips and connect the crankshaft position sensor connector.
| 13. INSTALL CAMSHAFT POSITION SENSOR |
Apply a light coat of engine oil to the O-ring of the sensor.
Install the camshaft position sensor with the bolt.
Connect the camshaft position sensor connector.
| 14. INSTALL VANE PUMP ASSEMBLY |
Install a new O-ring to the vane pump.
Install the vane pump with the 2 nuts.
| 15. INSTALL VACUUM PUMP ASSEMBLY |
Install 2 new O-rings to the vacuum pump.
Install the vacuum pump with the 2 nuts.
| 16. INSTALL ENGINE WATER PUMP ASSEMBLY |
Install a new gasket and the engine water pump with the 5 bolts and 2 nuts.
| 17. INSTALL NO. 2 TIMING BELT COVER |
![]() |
Apply seal packing (FIPG) to the specified areas shown in the illustration.
| *1 | Seal Packing |
Clean the bolts and their holes.
Apply adhesive to 2 or 3 threads at the end of each of the 4 bolts.
Install the No. 2 timing belt cover with the 4 bolts and nut.
| 18. INSTALL CAMSHAFT TIMING PULLEY |
Install the camshaft timing pulley.
Install the bolt of the camshaft timing pulley while holding the camshaft with a wrench.
| 19. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Install 4 new No. 3 cylinder head cover gaskets to the cylinder head cover in the directions shown in the illustration.
| *1 | No. 3 Cylinder Head Cover Gasket |
| *2 | Cylinder Head Cover |
Remove any old seal packing (FIPG material) from the cylinder head.
![]() |
Apply seal packing to the areas shown in the illustration.
![]() | Seal Packing |
Install a new cylinder head cover gasket to the cylinder head cover.
![]() |
Temporarily install the cylinder head cover with the 10 bolts and 2 nuts in the order shown in the illustration. Then, tighten the 10 bolts and 2 nuts in the order shown in the illustration in 2 progressive steps.
Connect the ventilation hose.
Install 4 new nozzle holder seals.
| 20. INSTALL NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY |
Install the No. 2 cylinder head cover with the 3 bolts.
| 21. INSTALL WIRING HARNESS CLAMP BRACKET |
Install the 2 wiring harness clamp brackets with the 3 bolts.
Attach the 6 wire harness clamps.
| 22. INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY |
![]() |
Temporarily install the No. 2 nozzle leakage pipe with the 3 bolts.
![]() | Union Bolt |
Temporarily install a new gasket and the union bolt.
Tighten the 3 bolts and union bolt.
| 23. INSTALL NO. 3 NOZZLE LEAKAGE PIPE |
![]() |
Apply a light coat of fuel to the O-ring of the fuel check valve.
| *1 | O-Ring |
Temporarily install the No. 3 nozzle leakage pipe with the 2 bolts.
Temporarily install a new gasket and the fuel check valve.
Tighten the 2 bolts and fuel check valve.
Connect the 3 fuel hoses.
| 24. INSTALL NO. 2 FUEL PIPE |
![]() |
Apply a light coat of fuel to the O-ring of the fuel check valve.
| *1 | O-Ring |
Install a new gasket to the No. 2 fuel pipe and temporarily install the fuel check valve.
Temporarily install a new gasket and the supply pump hollow screw.
Using a 6 mm hexagon wrench, tighten the supply pump hollow screw.
Tighten the fuel check valve.
| 25. INSTALL NO. 4 INJECTION PIPE SUB-ASSEMBLY |
Temporarily install the No. 4 injection pipe with the union nuts.
Install the 2 No. 2 injection pipe clamps with the bolt and nut.
Using a 17 mm union nut wrench, tighten the injection pipe union nut on the common rail side.
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.
| 26. INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND COOLER |
| 27. INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET |
Install the No. 1 compressor mounting bracket with the 4 bolts.
| 28. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Install the V-ribbed belt tensioner with the 4 bolts.
| *1 | Cylinder Block |
| *2 | V-ribbed Belt Tensioner |
| 29. INSTALL GENERATOR BRACKET |
Install the generator bracket with the bolt.
| 30. INSTALL GENERATOR ASSEMBLY |
![]() |
Install the generator and adjusting bar with the 2 bolts.
Install the generator wire with the nut.
Connect the generator connector.
| 31. INSTALL NO. 2 IDLE PULLEY ASSEMBLY |
Install the spacer, No. 2 idle pulley and pulley plate with the bolt.
| 32. INSTALL NO. 1 TIMING BELT IDLER SUB-ASSEMBLY |
Using a 10 mm hexagon wrench, install a new washer and the No. 1 timing belt idler with the bolt.
Check that the idler pulley moves smoothly.
If the idler pulley does not move smoothly, check the installation condition of the idler and washer.
| 33. INSTALL TIMING BELT |
![]() |
Check that the timing marks are aligned as shown in the illustration.
| *1 | Timing Mark |
Install the timing belt to the pump drive shaft pulley, camshaft timing pulley and No. 1 timing belt idler in sequence.
![]() |
Place the tensioner upright. Then set a press on the top of the tensioner.
Using the press, slowly push in the push rod using 981 to 9800 N (100 to 999 kgf, 220 to 2203 lbf) of force.
Align the holes of the push rod and housing. Then pass a 1.5 mm hexagon wrench through the holes to fix the push rod in place.
Temporarily install the timing belt tensioner with the 2 bolts while pushing the idler pulley toward the timing belt.
Tighten the 2 bolts.
![]() |
Remove the 1.5 mm hexagon wrench from the tensioner.
![]() |
Turn the crankshaft clockwise 720° and check that the timing marks are aligned as shown in the illustration.
| *1 | Timing Mark |
| 34. INSTALL NO. 1 TIMING BELT COVER |
Install the timing belt cover and 6 washers with the 6 bolts.
| 35. INSTALL ENGINE ASSEMBLY |
| 36. ADD ENGINE OIL |
Add new engine oil.
| Item | Oil Grade | Oil Viscosity (SAE) |
| w/ Glow Plug Controller | API CF-4, CF or ACEA B1 | - 5W-30 - 10W-30 - 15W-40 - 20W-50 (5W-30 is best choice for fuel economy and good starting in cold winter.) |
| w/o Glow Plug Controller | G-DLD1, API CF-4, CF or ACEA B1 | - 5W-30 - 10W-30 - 15W-40 - 20W-50 |
| Item | Specified Condition |
| Drain and refill without oil filter change | 6.6 liters (7.0 US qts, 5.8 Imp. qts) |
| Drain and refill with oil filter change | 6.9 liters (7.3 US qts, 6.1 Imp. qts) |
| Dry fill | 7.4 liters (7.8 US qts, 6.5 Imp. qts) |
Install the oil filler cap.
| 37. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 38. BLEED AIR FROM FUEL SYSTEM |
![]() |
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.
Check if the engine starts.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs (Click here).
Start the engine.*1
![]() |
Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak.*2
| *a | Reference (Active Test Operation) |
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.

Enter the following menus: Powertrain / Engine / DTC.
Read Current DTCs.
Clear the DTCs (Click here).
Repeat steps *1 to *3.
Enter the following menus: Powertrain / Engine / DTC.
Read Current DTCs.
| 39. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
![]() |
Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank's B line.
| Item | Specified Condition |
| A/T | 11.1 liters (11.7 US qts, 9.8 Imp. qts) |
| M/T | 9.8 liters (10.4 US qts, 8.6 Imp. qts) |
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
![]() |
Using a wrench, install the vent plug.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2,500 to 3,000 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
After the coolant cools down, check that the coolant level is at the F line.
If the coolant level is below the F line, add TOYOTA SLLC to the F line.
| 40. BLEED AIR FROM POWER STEERING SYSTEM |
Check the fluid level.
Jack up the front of the vehicle and support it with stands.
Turn the steering wheel.
With the engine stopped, turn the steering wheel slowly from lock to lock several times.
Lower the vehicle.
Start the engine. Run the engine at idle for a few minutes.
Turn the steering wheel.
With the engine idling, turn the steering wheel to the left or right full lock position and hold it there for 2 to 3 seconds. Then turn the steering wheel to the opposite full lock position and hold it there for 2 to 3 seconds.
Repeat the step above several times.
Stop the engine.
![]() |
Check for foaming or emulsification. If the system has to be bled twice because of foaming or emulsification, check for fluid leaks in the system.
Check the fluid level.
| 41. INSPECT FOR POWER STEERING FLUID LEVEL |
![]() |
Keep the vehicle level.
With the engine stopped, check the power steering fluid level in the oil reservoir. If necessary, add power steering fluid.
Start the engine and run it at idle.
Turn the steering wheel to the left or right full lock position, and then turn the wheel to the opposite full lock position. Repeat this several times to raise fluid temperature.
![]() |
Check for foaming or emulsification. If foaming or emulsification is identified, bleed air from the power steering system.
![]() |
With the engine idling, measure the fluid level in the oil reservoir.
Stop the engine.
Wait a few minutes and remeasure the fluid level in the oil reservoir.
Check the fluid level.
| 42. INSPECT FOR OIL LEAK |
Start the engine. Make sure that there are no oil leaks from the areas that were worked on.
| 43. INSPECT FOR COOLANT LEAK |
Check for engine coolant leaks (Click here).
| 44. INSPECT FOR EXHAUST GAS LEAK |
| 45. INSPECT FOR FUEL LEAK |
Perform the Active Test.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine / Active Test.
Perform the Active Test.
| Intelligent Tester Display | Test Part | Control Range | Diagnostic Note |
| Test the Fuel Leak | Pressurize common rail interior and check for fuel leaks | Stop/Start |
|
| 46. INSPECT ENGINE OIL LEVEL |
Warm up the engine, stop the engine and wait 5 minutes. The engine oil level should be between the dipstick low level mark and full level mark.
If low, check for leakage and add oil up to the full level mark.