INTAKE SYSTEM (w/o Glow Plug Controller) > ON-VEHICLE INSPECTION |
| 1. CHECK INTAKE MANIFOLD (w/o EGR Cooler) |
![]() |
Connect a vacuum gauge between the control valve and VSV.
Warm up the engine.
Measure the vacuum.
| Engine Condition | VSV Condition | Specified Condition |
| Normal engine speed | ON | Approx. 35 kPa (263 mmHg, 10.35 in.Hg) |
| 3000 rpm or more | OFF | 0 kPa (0 mmHg, 0 in.Hg) |
| 2. CHECK INTAKE AIR SYSTEM |
Check for leakage or clogging between the air cleaner housing and turbocharger inlet, and between the turbocharger outlet and cylinder head.
| Condition | Operation |
| Clogged air cleaner | Clean or replace |
| Collapsed or deformed hoses | Repair or replace |
| Leakage from connections | Check each connection and repair |
| Cracks in components | Check and replace |
| 3. CHECK EXHAUST SYSTEM |
Check for leakage or clogging between the cylinder head and turbocharger inlet, and between the turbocharger outlet and exhaust pipe.
| Condition | Operation |
| Deformed components | Repair or replace |
| Foreign matter in passages | Remove |
| Leakage from components | Repair or replace |
| Cracks in components | Check or replace |
| 4. CHECK BOOST PRESSURE |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
![]() |
Take a snapshot of the Data List items with the intelligent tester shown in the illustration.
| *1 | Snapshot Record Button |
Compare MAP with Target Booster Pressure.
Warm up the engine.
![]() |
Using a 3-way connector, connect SST (turbocharger pressure gauge) between the manifold absolute pressure sensor and the gas filter.
Fully apply the parking brake and chock the 4 wheels.
for Manual Transmission:
While depressing the clutch pedal, fully depress the accelerator pedal. Measure the boost pressure at maximum engine speed (approximately 4600 rpm).
for Automatic Transmission:
Move the shift lever to P or N, and then fully depress the accelerator pedal. Measure the boost pressure at maximum engine speed (approximately 4600 rpm).
Chart showing the suspected trouble areas when the pressure is below the standard.
| Item | MAP (Absolute pressure inside intake manifold) | MAF (Intake air flow rate) | Accel Position | Actual Throttle Position | Actual EGR Valve Pos. | EGR Close Lrn. Status (EGR valve fully closed position learning status) | Fuel Pressure | Injection Feedback Val #1 (to #4) |
| Values taken from an actual normal vehicle *1 | - | 90 g/sec. | 99% or more | 0% | 0% | OK | - | -3 to +3 mm3/st |
| Values which represent a malfunction *1 | MAP is below Target Booster Pressure by 30 kPa or more | MAF is less than 81 g/sec. | Accel Position is not fully depressed position *2 | Actual Throttle Position is not fully open position | Actual EGR Valve Pos. is not valve fully closed position *3 | NG (Determined after performing learning) | Fuel Pressure is below Target Common Rail Pressure by 10 MPa or more (Check while condition steady) | Outside of above range |
| Turbocharger | ○ | ○ | - | - | - | - | - | - |
| EGR valve does not close or has problem with movement | ○ | ○ | - | - | ○ (Problem with EGR valve movement) *4 | ○ (EGR valve does not close) *4 | - | - |
| Problem with diesel throttle movement | ○ (Intake airflow decreases) | ○ | - | ○ | - | - | - | - |
| Accelerator pedal cannot be fully depressed or problem with accelerator pedal position sensor exists | - | ○ | ○ | - | - | - | - | - |
| Intake air system leakage or blockage | ○ | ○ | - | - | - | - | - | - |
| Exhaust gas leakage before turbocharger or blockage | ○ | ○ | - | - | - | - | - | - |
| Manifold absolute pressure sensor | ○ | ○ | - | - | - | - | - | - |
| Manifold absolute pressure sensor hose is disconnected | ○ | ○ | - | - | - | - | - | - |
| Mass air flow meter sub-assembly | - | ○ | - | - | - | - | - | - |
| Fuel system (injector, supply pump or common rail) | ○ | ○ | - | - | - | - | ○ (Fuel injector leakage, decrease in pressure discharge valve relief pressure or valve is stuck) | ○ *5 |
| 5. INSPECT MANIFOLD ABSOLUTE PRESSURE SENSOR |
Inspect the power source voltage.
Disconnect the manifold absolute pressure sensor connector.
![]() |
Measure the voltage according to the value(s) in the table below.
If the result is not as specified, inspect the wire harness or ECM (Click here).
| Tester Connection | Switch Condition | Specified Condition |
| 3 VC (+) - 1 E (-) | Ignition switch ON | 4.75 to 5.25 V |
| *a | Front view of wire harness connector (to Manifold Absolute Pressure Sensor) |
![]() |
Connect the manifold absolute pressure sensor connector.
Check the power supply.
Turn the ignition switch to ON.
Disconnect the vacuum hose from the manifold absolute pressure sensor.
![]() |
Measure the voltage according to the value(s) in the table below.
If the result is not as specified, replace the manifold absolute pressure sensor.
| Tester Connection | Condition | Specified Condition |
| E6-28 (PIM +) - E7-28 (E2 -) | 13.3 kPa (100 mmHg, 3.94 in.Hg) | 0.0 to 0.3 V |
| 26.6 kPa (199 mmHg, 7.85 in.Hg) | 0.1 to 0.4 V | |
| 40 kPa (300 mmHg, 11.81 in.Hg) | 0.3 to 0.6 V |
| Tester Connection | Condition | Specified Condition |
| E6-28 (PIM +) - E7-28 (E2 -) | 13.3 kPa (100 mmHg, 3.94 in.Hg) | 0.1 to 0.4 V |
| 26.6 kPa (199 mmHg, 7.85 in.Hg) | 0.2 to 0.6 V | |
| 40 kPa (300 mmHg, 11.81 in.Hg) | 0.4 to 0.8 V |
![]() |
Using SST, measure the voltage according to the value(s) in the table below.
If the result is not as specified, replace the manifold absolute pressure sensor.
| Tester Connection | Condition | Specified Condition |
| E6-28 (PIM +) - E7-28 (E2 -) | 19.6 kPa (0.20 kgf/cm2, 2.84 psi) | 0.05 to 0.3 V |
| 39.2 kPa (0.40 kgf/cm2, 5.68 psi) | 0.25 to 0.55 V | |
| 58.8 kPa (0.60 kgf/cm2, 8.53 psi) | 0.45 to 0.75 V | |
| 78.5 kPa (0.80 kgf/cm2, 11.4 psi) | 0.65 to 0.95 V | |
| 98.0 kPa (1.00 kgf/cm2, 14.2 psi) | 0.9 to 1.2 V |
| Tester Connection | Condition | Specified Condition |
| E6-28 (PIM +) - E7-28 (E2 -) | 19.6 kPa (0.20 kgf/cm2, 2.84 psi) | 0.1 to 0.4 V |
| 39.2 kPa (0.40 kgf/cm2, 5.68 psi) | 0.4 to 0.7 V | |
| 58.8 kPa (0.60 kgf/cm2, 8.53 psi) | 0.7 to 1.0 V | |
| 78.5 kPa (0.80 kgf/cm2, 11.4 psi) | 1.0 to 1.3 V | |
| 98.0 kPa (1.00 kgf/cm2, 14.2 psi) | 1.3 to 1.6 V |
| 6. CHECK MOTOR FOR TURBOCHARGER CONTROL OPERATION |
Remove the No. 1 exhaust manifold heat insulator and No. 1 turbo insulator .
Check the stroke.
Turn the ignition switch from ON to off.
Check the operation of the DC motor. Check that the motor rod stroke is as shown in A to D in the illustration below.
After the DC motor operates, visually check that the vane activation link contacts the fully closed stopper.

| *1 | Motor Rod | *2 | Lock Nut |
| *3 | Fully Closed Stopper | *4 | Ignition Switch |
| *a | Motor Rod Stroke | *b | Fully Closed Stopper Contact |
| *c | Ignition Switch OFF Time | - | - |
| 7. CHECK TURBO MOTOR DRIVER |
![]() |
Check the voltage of the turbo motor driver.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
If the result is not as specified, refer to the following procedures (Click here).
| Tester Connection | Specified Condition |
| T32-3 (+B) - Body ground | 9 to 14 V |
![]() |
Check the resistance of the wire harness side connector.
Turn the ignition switch off.
Disconnect the turbo motor driver connector.
Measure the resistance according to the value(s) in the table below.
If the result is not as specified, refer to the following procedures (Click here).
| Tester Connection | Specified Condition |
| T32-4 (GND) - Body ground | Below 1 Ω |
Connect the turbo motor drive connector.
Check the turbo motor signal.

| Tester Connection | Tool Setting | Condition | Specified Condition |
| (a) Between E7-10 (VNTO) and E6-7 (E1) (b) Between E7-17 (VNTI) and E6-7 (E1) | (a) 5 V/Division, 20 msec./Division (b) 5 V/Division, 50 msec./Division | Idling with warm engine | Refer to illustration |
Connect an oscilloscope to the terminals of the ECM.
While idling the engine, check the waveform of the ECM.