Home › BODY ELECTRICAL › WIPER AND WASHER › WIPER SWITCH

WIPER SWITCH > INSPECTION

for Preparation Click here



1. INSPECT WIPER AND WASHER SWITCH ASSEMBLY (for LHD)


B113575E02
  1. Measure the resistance of the switch.
    Standard resistance :

    Windshield wiper switch:
    Tester Connection
    Switch Condition
    Specified Condition
    B-3 (+1) - B-2 (+B)
    MIST
    Below 1 Ω
    B-3 (+1) - B-1 (+S)
    OFF
    Below 1 Ω
    B-3 (+1) - B-1 (+S)
    INT
    Below 1 Ω
    B-3 (+1) - B-2 (+B)
    LO
    Below 1 Ω
    B-4 (+2) - B-2 (+B)
    HI
    Below 1 Ω

    Windshield washer switch:
    Tester Connection
    Switch Condition
    Specified Condition
    A-3 (WF) - A-2 (EW)
    OFF
    10 kΩ or higher
    A-3 (WF) - A-2 (EW)
    ON
    Below 1 Ω

    Rear wiper and washer switch:
    Tester Connection
    Switch Condition
    Specified Condition
    A-2 (EW) - B-5 (WR)
    WASH
    (Rear wiper switch ON position side)
    Below 1 Ω
    A-2 (EW) - B-5 (WR)
    OFF
    10 kΩ or higher
    A-7 (+1R) - B-5 (WR)
    OFF
    10 kΩ or higher
    A- 2 (EW) - A-7 (+1R)
    OFF
    10 kΩ or higher
    A- 2 (EW) - A-7 (+1R)
    ON
    Below 1 Ω
    A-2 (EW) - B-5 (WR)
    WASH
    (Rear wiper switch ON position side)
    Below 1 Ω
    A-7 (+1R) - B-5 (WR)
    WASH
    (Rear wiper switch ON position side)
    Below 1 Ω
    A-2 (EW) - A-7 (+1R)
    WASH
    (Rear wiper switch ON position side)
    Below 1 Ω

    If the result is not as specified, replace the switch assembly.



  1. Check the intermittent operation.

    1. Connect the voltmeter's positive (+) lead to terminal B-3 (+1) and the negative (-) lead to terminal A-2 (EW).

    2. Connect the battery's positive (+) lead to terminal B-2 (+B) and the negative (-) lead to terminals A-2 (EW) and B-1 (+S).

    3. Turn the wiper switch to the INT position.

    4. Connect the battery's positive (+) lead to terminal B-1 (+S) for 5 seconds.



    5. Connect the battery's negative (-) lead to terminal B-1 (+S). Operate the intermittent wiper relay and check the voltage between terminals B-3 (+1) and A-2 (EW).

      OK:
      Refer to illustration below.



      E146261E01

      If the result is not as specified, replace the switch assembly.



  1. Check the washer operation.

    1. Turn the wiper switch OFF.

    2. Connect the battery's positive (+) lead to terminal B-2 (+B) and the negative (-) lead to terminals B-1 (+S) and A-2 (EW).

    3. Connect the voltmeter's positive (+) lead to terminal B-3 (+1) and the negative (-) lead to terminal A-2 (EW).



    4. Turn the washer switch ON and OFF, and check the voltage between terminals B-3 (+1) and A-2 (EW).

      OK:
      Refer to illustration below.



      B086335E03

      If the result is not as specified, replace the switch assembly.



2. INSPECT WIPER AND WASHER SWITCH ASSEMBLY (for RHD)


B086316E02
  1. Measure the resistance of the switch.
    Standard resistance :

    Windshield wiper switch:
    Tester Connection
    Switch Condition
    Specified Condition
    B-2 (+1) - B-3 (+B)
    MIST
    Below 1 Ω
    B-2 (+1) - B-4 (+S)
    OFF
    Below 1 Ω
    B-2 (+1) - B-4 (+S)
    INT
    Below 1 Ω
    B-2 (+1) - B-3 (+B)
    LO
    Below 1 Ω
    B-1 (+2) - B-3 (+B)
    HI
    Below 1 Ω

    Windshield washer switch:
    Tester Connection
    Switch Condition
    Specified Condition
    A-1 (WF) - A-2 (EW)
    OFF
    10 kΩ or higher
    A-1 (WF) - A-2 (EW)
    ON
    Below 1 Ω

    Rear wiper and washer switch:
    Tester Connection
    Switch Condition
    Specified Condition
    A-2 (EW) - B-10 (WR)
    WASH
    (Rear wiper switch ON position side)
    Below 1 Ω
    A-2 (EW) - B-10 (WR)
    OFF
    10 kΩ or higher
    A-4 (+1R) - B-10 (WR)
    OFF
    10 kΩ or higher
    A-2 (EW) - A-4 (+1R)
    OFF
    10 kΩ or higher
    A-2 (EW) - A-4 (+1R)
    ON
    Below 1 Ω
    A-2 (EW) - B-10 (WR)
    WASH
    (Rear wiper switch ON position side)
    Below 1 Ω
    A-4 (+1R) - B-10 (WR)
    WASH
    (Rear wiper switch ON position side)
    Below 1 Ω
    A-2 (EW) - A-4 (+1R)
    WASH
    (Rear wiper switch ON position side)
    Below 1 Ω

    If the result is not as specified, replace the switch assembly.



  1. Check the intermittent operation.

    1. Connect the voltmeter's positive (+) lead to terminal B-2 (+1) and the negative (-) lead to terminal A-2 (EW).

    2. Connect the battery's positive (+) lead to terminal B-3 (+B) and the negative (-) lead to terminals A-2 (EW) and B-4 (+S).

    3. Turn the wiper switch to the INT position.

    4. Connect the battery's positive (+) lead to terminal B-4 (+S) for 5 seconds.



    5. Connect the battery's negative (-) lead to terminal B-4 (+S). Operate the intermittent wiper relay and check the voltage between terminals B-2 (+1) and A-2 (EW).

      OK:
      Refer to illustration below.



      E146261E02

      If the result is not as specified, replace the switch assembly.



  1. Check the washer operation.

    1. Turn the wiper switch OFF.

    2. Connect the battery's positive (+) lead to terminal B-3 (+B) and the negative (-) lead to terminals B-4 (+S) and A-2 (EW).

    3. Connect the voltmeter's positive (+) lead to terminal B-2 (+1) and the negative (-) lead to terminal A-2 (EW).



    4. Turn the washer switch ON and OFF, and check the voltage between terminals B-2 (+1) and A-2 (EW).

      OK:
      Refer to illustration below.



      B086335E04

      If the result is not as specified, replace the switch assembly.