Home › STEERING › POWER STEERING › POWER STEERING LINK

POWER STEERING LINK > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



2. PLACE FRONT WHEEL FACING STRAIGHT AHEAD


3. REMOVE STEERING PAD ASSEMBLY


    B281336E01
  1. Using a T30 "TORX" socket wrench, loosen the 2 screws until the groove along the screw circumference catches on the screw case.
    Text in Illustration 
    *1
    Screw Case



    B277210
  1. Pull out the steering pad from the steering wheel as shown in the illustration. Then support the steering pad with one hand.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Disconnect the horn connector.

  1. Disconnect the connector and remove the steering pad.

    NOTICE:
    When handling the airbag connector, do not damage the airbag wire harness.



4. REMOVE STEERING WHEEL ASSEMBLY


    C240367E02
  1. Remove the steering wheel set nut.

  1. Place matchmarks on the steering wheel and main shaft.

  1. Using SST, remove the steering wheel.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)



5. REMOVE STEERING COLUMN COVER LOWER


    C238860
  1. Remove the 3 screws and lower cover.



6. REMOVE STEERING COLUMN COVER UPPER


7. REMOVE WINDSHIELD WIPER SWITCH ASSEMBLY


    E225945
  1. Disconnect the connectors.

  1. Detach the claw and remove the windshield wiper switch.

    NOTICE:
    Do not push the claw with excessive force as damage may occur.



8. REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY


    B088653
  1. Disconnect the connector.



    B088654
  1. Using needle-nose pliers, remove the band clamp as shown in the illustration.



    E177501
  1. While loosening the band clamp as shown in the illustration, detach the claw to remove the headlight dimmer switch assembly.

    NOTICE:
    If the claw is pressed forcefully, it will break.



9. REMOVE SPIRAL CABLE SUB-ASSEMBLY


B110259E02
  1. Disconnect the connectors from the spiral cable.

    NOTICE:
    When handling the airbag connector, do not damage the airbag wire harness.

  1. Detach the 3 claws and remove the spiral cable.



10. REMOVE FRONT WHEEL


11. REMOVE NO. 2 ENGINE UNDER COVER
  1. Remove the 4 bolts and under cover.



12. REMOVE NO. 1 ENGINE UNDER COVER
  1. Remove the 4 bolts and under cover.



13. REMOVE FRONT SIDE MEMBER TO FRONT SUSPENSION CROSSMEMBER BRACE
  1. Remove the 8 bolts and crossmember brace.



14. REMOVE FRONT STABILIZER BAR
  1. Remove the stabilizer bar front from the vehicle body.



15. DISCONNECT TIE ROD END SUB-ASSEMBLY LH
  1. Remove the cotter pin and nut.



    G034366E01
  1. Using SST, disconnect the tie rod end from the steering knuckle arm.

    SST
    09628-62011  



16. DISCONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



17. DISCONNECT STEERING SLIDING YOKE


    C239647E02
  1. Loosen the bolt labeled A.

  1. Make matchmarks on the steering yoke and steering intermediate shaft.

  1. Remove the bolt labeled B.

  1. Disconnect the steering sliding yoke from the No. 2 steering intermediate shaft.



18. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


    C239648E02
  1. Make matchmarks on the intermediate shaft and steering link.

  1. Remove the bolt and intermediate shaft from the steering link.

    NOTICE:
    If the intermediate shaft is struck, replace it with a new one.



19. DISCONNECT PRESSURE FEED TUBE ASSEMBLY


    G100745E03
  1. Using a union nut wrench, loosen the flare nut and disconnect the pressure feed tube.



    G100746
  1. Remove the bolt and disconnect the pressure feed tube from the steering link.



20. DISCONNECT STEERING GEAR OUTLET RETURN TUBE


    G100747
  1. Disengage the clip and disconnect the return hose.



    G100748E04
  1. Using a union nut wrench, disconnect the outlet return tube.



21. REMOVE POWER STEERING LINK ASSEMBLY


    G100749
  1. Fix the 2 nuts in place and remove the 2 bolts. Then remove the link from the frame.

    NOTICE:
    Never turn the nut. Be sure to turn the bolt.

    HINT:
    Removal of the link may be easier if the following is performed: 1) remove the differential mount, and 2) slide the differential toward the rear of the vehicle.