DTC P0115 Engine Coolant Temperature Circuit |
DTC P0117 Engine Coolant Temperature Circuit Low Input |
DTC P0118 Engine Coolant Temperature Circuit High Input |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch to ON for 0.5 seconds | Open or short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic). |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch to ON for 0.5 seconds | Short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic). |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch to ON for 0.5 seconds | Open in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic). |
|
| DTC No. | Data List |
| P0115 | Coolant Temp |
| P0117 | |
| P0118 |
| Temperature Displayed | Malfunction |
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) or higher | Short circuit |

| 1.READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the value.
| Result | Proceed to |
| -40°C (-40°F) | A |
| 140°C (284°F) or higher | B |
| 70 to 90°C (158 to 194°F) | C |
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS) |
![]() |
Disconnect the engine coolant temperature sensor connector.
Connect terminals 1 and 2 of the engine coolant temperature sensor wire harness side connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the value.
| *1 | Engine Coolant Temperature Sensor |
| *2 | ECM |
| *a | Front view of wire harness connector (to Engine Coolant Temperature Sensor) |
Reconnect the engine coolant temperature sensor connector.
|
| ||||
|
| ||||
| 3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) |
Disconnect the engine coolant temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| W1-2 - E7-19 (THW) | Always | Below 1 Ω |
| W1-1 - E7-28 (E2) | Always | Below 1 Ω |
Reconnect the engine coolant temperature sensor connector.
Reconnect the ECM connector.
|
| ||||
|
| ||||
| 4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS) |
![]() |
Disconnect the engine coolant temperature sensor connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the value.
| *1 | Engine Coolant Temperature Sensor |
| *2 | ECM |
Reconnect the engine coolant temperature sensor connector.
|
| ||||
|
| ||||
| 5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) |
Disconnect the engine coolant temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| W1-2 or E7-19 (THW) - Body ground | Always | 10 kΩ or higher |
Reconnect the engine coolant temperature sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 6.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 7.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR. |
Replace the engine coolant temperature sensor (Click here).
|
| ||||
| 8.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
|
| ||||
| 9.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM. |
Replace the ECM (Click here).
|
| ||||
| 10.REPLACE ENGINE COOLANT TEMPERATURE SENSOR |
Replace the engine coolant temperature sensor (Click here).
| NEXT | |
| 11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch to ON for 1 second.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||