DTC P1238 Injector Malfunction |

| *A | Injector Cross Section Diagram: | - | - |
| *1 | Solenoid Valve | *2 | Piston |
| *3 | Nozzle Needle | - | - |
| DTC Detection Drive Pattern | DTC Detection Condition | Main Trouble Area | Related Trouble Area |
| Warm up the engine and idle it for 60 seconds | A large engine speed fluctuation when idling continues for 60 seconds (2 trip detection logic). |
|
|
| DTC No. | Data List |
| P1238 |
|
| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1238) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P1238 is output | A |
| P1238 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (ENGINE WIRE HARNESS) |
Check the wire harness and connector connections.
|
| ||||
| OK | |
| 3.CHECK INJECTOR COMPENSATION CODE |
Read the injector compensation codes .
|
| ||||
| OK | |
| 4.READ VALUE USING INTELLIGENT TESTER (COMPENSATORY INJECTION VOLUME FOR EACH CYLINDER) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Val #1 to #4.
Read the value.
Inspect and repair the cylinder that has an improper compensation value according to the following steps.
| NEXT | |
| 5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.
Check the 4 cylinders in sequence to identify any faulty cylinders by performing the power-balance inspection.
| NEXT | |
| 6.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER |
Check the cylinder compression pressure .
|
| ||||
| OK | |
| 7.REPLACE INJECTOR ASSEMBLY |
Replace the injector assembly (Click here).
| NEXT | |
| 8.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 9.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING |
Register the injector compensation code .
Perform the injector pilot quantity learning .
| NEXT | |
| 10.CHECK WHETHER DTC OUTPUT RECURS (DTC P1238) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Start the engine.
Warm up the engine (engine coolant temperature is 70°C (158°F) or higher) and idle it for 60 seconds (the shift lever should be in neutral, and the A/C switch and all accessory switches should be off).
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the pending DTCs.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTC P1238.
Check the DTC judgment result.
| Tester Display | Result | Proceed to |
| Pending DTC | P1238 is output | A |
| All Readiness | ABNORMAL | A |
| NORMAL | B |
|
| ||||
| A | |
| 11.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 12.CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION |
|
| ||||
| 13.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Start the engine.
Warm up the engine (engine coolant temperature is 70°C (158°F) or higher) and idle it for 60 seconds (the shift lever should be in neutral, and the A/C switch and all accessory switches should be off).
Confirm that the DTC is not output again.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTC P1238.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, increase the idling time.
| NEXT | ||
| ||