Home › BODY › SEAT › REAR NO. 2 SEAT ASSEMBLY

REAR NO. 2 SEAT ASSEMBLY > REASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the RH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).

CAUTION:
Wear protective gloves. Sharp areas on the seatback frames and seat cushion frame may injure your hands,



1. INSTALL NO. 2 SEAT LEG PLATE
  1. Install the plate with the 2 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



2. INSTALL REAR NO. 2 SEAT CUSHION COVER

NOTICE:

  1. B125788E01
  2. Be careful not to damage the cover.
  3. When installing the hog rings, avoid wrinkling the cover.

  1. Except TASA made:
    Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 6 new hog rings.

  1. TASA made:

  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 4 new hog rings.
    Install the seat cushion cover (with pad) to the seat cushion frame with the hook.



3. INSTALL REAR SEAT CUSHION UNDER CLOTH


4. INSTALL NO. 1 SEAT CUSHION CARPET


    B089770E01
  1. Set the carpet onto the seat cushion.

  1. Using a tacker, install the carpet to the seat cushion with the 4 tack pins and 2 clips, as shown in the illustration.

    NOTICE:
    Do not substitute other metal parts for tack pins.



5. INSTALL NO. 2 SEAT LEG SUB-ASSEMBLY RH


    B118020
  1. Install the leg with the 2 bolts and No. 3 seat cushion spring.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



6. INSTALL REAR NO. 2 SEAT BELT SUB-ASSEMBLY INNER


    B118019
  1. Pass the belt through the hole in the seat cushion cover (with pad). Install the inner belt and lap type belt to the No. 2 seat cushion frame with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



7. INSTALL REAR SEAT LEG COVER


    B089767E02
  1. Attach the 2 claws to install the leg cover.

  1. Install the 3 screws.



8. INSTALL NO. 2 SEAT CUSHION COVER RH


    B089765E01
  1. Pass the fold seat stopper band through the hole in the No. 2 seat cushion cover. Then install the fold seat stopper band to the seat cushion frame with the screw.

  1. Install the No. 2 seat cushion cover with the 5 screws.

  1. Install the rear No. 2 seat cushion cover to the No. 2 seat cushion cover.



    B118018E01
  1. Attach the 14 claws and hooks.



9. INSTALL REAR NO. 2 SEAT COVER RH


    B118017E01
  1. Pass the fold seat stopper band through the hole in the rear No. 2 seat cover RH.

  1. Install the rear No. 2 seat cover RH with the screw.

  1. Fold the fold seat stopper band and install the 2 lock release buttons as shown in the illustration.



10. INSTALL REAR SEAT HINGE COVER


    B089762E01
  1. Attach the 2 claws to install the hinge cover.

  1. Install the 2 screws.



11. INSTALL NO. 3 SEAT OUTER REAR LEG SUB-ASSEMBLY RH
  1. Install the leg with the 2 plates and bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



12. INSTALL NO. 3 SEAT OUTER FRONT LEG SUB-ASSEMBLY RH
  1. Install the leg with the 2 plates and bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



13. INSTALL REAR NO. 2 SEATBACK COVER

NOTICE:

  1. B118016E01
  2. Be careful not to damage the cover.
  3. When installing the hog rings, avoid wrinkling the cover.

  1. Using hog ring pliers, install the seatback cover to the seatback pad with 3 new hog rings.

  1. Install the seatback cover (with pad) to the seatback frame.



    B085727E01
  1. Install the 2 headrest supports.



    B125791E01
  1. Attach the hook labeled B or close the fastening tape labeled B.

    HINT:
    1. Depending on the type of seat cover, hooks or fastening tape is present.
    2. Tape the screwdriver tip before use.

  1. Close the fastening tape labeled A.

  1. Attach the hooks.



14. INSTALL REAR NO. 2 SEATBACK ASSEMBLY


    B086030E02
  1. LH side:
    Install the seatback with the plate, spacer and bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. RH side:
    Install the seatback with the 2 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



15. INSTALL REAR NO. 2 SEAT RECLINING COVER RH


B085723E01
  1. Install the reclining cover with the 2 screws.



16. INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE RH


B085725E01
  1. Install the release handle with the screw.



17. INSTALL REAR SEAT CUSHION HINGE COVER LOWER RH


B085724E01
  1. Install the hinge cover with the 2 screws.



18. INSTALL REAR NO. 2 SEAT HEADREST ASSEMBLY RH