Home › ENGINE ยท 1GR-FE › CHARGING › GENERATOR (for DENSO Made)

GENERATOR (for DENSO Made) > REASSEMBLY

for Preparation Click here



1. INSTALL GENERATOR ROTOR ASSEMBLY
  1. Install the generator rotor.

  1. Install the generator washer onto the rotor.



2. INSTALL GENERATOR RECTIFIER END FRAME


A121969E01
  1. Using a 19 mm socket wrench and press, slowly press in the rectifier end frame.

  1. Install the 4 nuts.

    Torque:
    4.5 N*m{ 46 kgf*cm , 40 in.*lbf }

  1. Install the seal plate onto the rectifier end frame.



    A121970E01
  1. Install the 3 rubber insulators onto the lead wires.

    NOTICE:
    Be careful that the rubber insulators are in the right direction.



3. INSTALL GENERATOR HOLDER WITH RECTIFIER
  1. Install the rectifier holder while pushing it with the 3 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



4. INSTALL VOLTAGE REGULATOR ASSEMBLY
  1. Install the 3 screws and voltage regulator.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



5. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY


A121971E01
  1. Install the brush holder with the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }

    NOTICE:
    Make sure to install the holder in the correct direction.

  1. Install the brush holder cover.



6. INSTALL GENERATOR REAR END COVER


    A121962
  1. Install the end cover and plate terminal with the bolt and 3 nuts.

    Torque:
    3.9 N*m{ 40 kgf*cm , 34 in.*lbf } for bolt
    4.4 N*m{ 45 kgf*cm , 39 in.*lbf } for nut

  1. Install the terminal insulator with the nut.

    Torque:
    4.1 N*m{ 42 kgf*cm , 36 in.*lbf }



7. INSTALL GENERATOR PULLEY
  1. Temporarily install the generator pulley by the hand.

  1. Mount the generator in a vise between aluminum plates.



    A218210E01
  1. Install SST 1-A to the pulley shaft.

    SST
    09820-63010   (09820-06010, 09820-06020)
    SST 1-A and B
    09820-06010
    SST 2
    09820-06020

  1. Install SST 1-B to SST 1-A.

  1. Hold SST 1-A with a torque wrench and turn SST 1-B clockwise with the specified torque.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }

    NOTICE:
    Make sure that SST is secured to the rotor shaft.



    A218193E02
  1. Insert SST 2 and attach it to the pulley nut.



    A218192E01
  1. Tighten the pulley nut by turning SST 1-A in the direction shown in the illustration.

    Torque:
    133 N*m{ 1356 kgf*cm , 98 ft.*lbf }

  1. Remove SST 2 from the generator.



    A218211E01
  1. Turn SST 1-B in the direction shown in the illustration and remove SST 1-A and B.

  1. Turn the generator pulley and check that the generator pulley moves smoothly.