Home › TRANSMISSION · A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV with i-ART)

DTC    P0705    Transmission Range Sensor Circuit Malfunction (PRNDL Input)

for Preparation Click here


DESCRIPTION

The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the TCM.

DTC Code
DTC Detection Condition
Trouble Area
P0705
One of the following conditions is met:
(A) Any 2 or more of the following signals are ON simultaneously (2-trip detection logic):
  1. NSW input signal is ON
  2. R input signal is ON
  3. D input signal is ON
  4. 3 input signal is ON
  5. 2 input signal is ON
(B) Any of the following signals is ON for 2.0 sec. or more with the shift lever in 4 or L (2-trip detection logic):
  1. NSW input signal is ON
  2. R input signal is ON
  3. 3 input signal is ON
(C) All switches are OFF simultaneously for NSW, R, D, 3, and 2 (2-trip detection logic).
  1. Open or short in park/neutral position switch circuit
  2. Transmission control switch (shift lock control unit assembly)
  3. Park/neutral position switch
  4. TCM

MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch and wire harness in the park/neutral position switch circuit.
The park/neutral position switch and transmission control switch detects the shift lever position (R, D, 4, 3, 2, or L) and sends a signal to the TCM.
For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The TCM determines that there is a problem with the switch or related parts if it receives more than 1 of the R, D, 3 or 2 position signals simultaneously. The TCM will illuminate the MIL and store the DTC.

WIRING DIAGRAM


C237622E04


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Turn the ignition switch off.
  2. Connect the GTS to the DLC3.
  3. Turn the ignition switch to ON.
  4. Turn the GTS on.
  5. Enter the following menus: Powertrain / ECT / Data List / All Data.
  6. According to the display on the GTS, read the Data List.

    ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Neutral Position SW Signal
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in P and N
    2. ON: Shift lever in P or N
    When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    Shift SW Status (R Range)
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in R
    2. ON: Shift lever in R
    When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    Shift SW Status (D Range)
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in D
    2. ON: Shift lever in D
    When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    Shift SW Status (2 Range)
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in 2 and L
    2. ON: Shift lever in 2 or L
    When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    Shift SW Status (L Range)
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in L
    2. ON: Shift lever in L
    When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    Shift SW Status (4 Range)
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in D and 4
    2. ON: Shift lever in D or 4
    When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    Shift SW Status (3 Range)
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in 3
    2. ON: Shift lever in 3
    When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
1.CHECK HARNESS AND CONNECTOR (ECU-IG&GAUGE FUSE - PARK/NEUTRAL POSITION SWITCH)


    C197711E88
  1. Disconnect the park/neutral position switch connector.

  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
N1-2 (RB) - Body ground
Ignition switch ON
11 to 14 V
N1-2 (RB) - Body ground
Ignition switch off
Below 1 V

Text in Illustration 
*1
Front view of wire harness connector
(to Park/Neutral Position Switch)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)
  1. Disconnect the C163 ECM connector.



    C197711E89
  1. Disconnect the park/neutral position switch connector.

  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
N1-4 (B) - Body ground
Ignition switch ON
11 to 14 V
N1-4 (B) - Body ground
Ignition switch off
Below 1 V

Text in Illustration 
*1
Front view of wire harness connector
(to Park/Neutral Position Switch)


NG
Go to step 7
OK


3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C197712E41
  1. Disconnect the park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
4 (B) - 5 (L)
Shift lever in P or N
Below 1 Ω
2 (RB) - 1 (RL)
Shift lever in R
Below 1 Ω
2 (RB) - 7 (DL)
Shift lever in D or 4
Below 1 Ω
2 (RB) - 3 (2L)
Shift lever in 3
Below 1 Ω
2 (RB) - 8 (LL)
Shift lever in 2 or L
Below 1 Ω
4 (B) - 5 (L)
Shift lever not in P or N
10 kΩ or higher
2 (RB) - 1 (RL)
Shift lever not in R
10 kΩ or higher
2 (RB) - 7 (DL)
Shift lever not in D or 4
10 kΩ or higher
2 (RB) - 3 (2L)
Shift lever not in 3
10 kΩ or higher
2 (RB) - 8 (LL)
Shift lever not in 2 or L
10 kΩ or higher

Text in Illustration 
*1
Component without harness connected
(Park/Neutral Position Switch)


NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


4.INSPECT TRANSMISSION CONTROL SWITCH


    C214966E06
  1. Disconnect the transmission control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    9 (NSSD) - 3 (AT4)
    Shift lever in D
    10 kΩ or higher
    Shift lever in 4
    Below 1 Ω
    10 (NSSL) - 4 (ATL)
    Shift lever in 2
    10 kΩ or higher
    Shift lever in L
    Below 1 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Transmission Control Switch)



NG
REPLACE TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY) (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TRANSMISSION CONTROL SWITCH)


    C203405E12
  1. Disconnect the transmission control switch connector.

  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
S30-9 (NSSD) - Body ground
  1. Ignition switch ON
  2. Shift lever in D or 4
11 to 14 V
S30-9 (NSSD) - Body ground
  1. Ignition switch ON
  2. Shift lever not in D or 4
Below 1 V
S30-10 (NSSL) - Body ground
  1. Ignition switch ON
  2. Shift lever in 2 or L
11 to 14 V
S30-10 (NSSL) - Body ground
  1. Ignition switch ON
  2. Shift lever not in 2 or L
Below 1 V

Text in Illustration 
*1
Front view of wire harness connector
(to Transmission Control Switch)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)


    C212050E17
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    T36-9 (R) - T19-1 (E1)
    1. Ignition switch ON
    2. Shift lever in R
    11 to 14 V*
    T36-8 (D) - T19-1 (E1)
    1. Ignition switch ON
    2. Shift lever in D or 4
    11 to 14 V
    T36-13 (4) - T19-1 (E1)
    1. Ignition switch ON
    2. Shift lever in 4
    11 to 14 V
    T36-12 (3) - T19-1 (E1)
    1. Ignition switch ON
    2. Shift lever in 3
    11 to 14 V
    T36-11 (2) - T19-1 (E1)
    1. Ignition switch ON
    2. Shift lever in 2 or L
    11 to 14 V
    T36-10 (L) - T19-1 (E1)
    1. Ignition switch ON
    2. Shift lever in L
    11 to 14 V
    T36-9 (R) - T19-1 (E1)
    1. Ignition switch ON
    2. Shift lever not in R
    Below 1 V
    T36-8 (D) - T19-1 (E1)
    1. Ignition switch ON
    2. Shift lever not in D or 4
    Below 1 V
    T36-13 (4) - T19-1 (E1)
    1. Ignition switch ON
    2. Shift lever not in 4
    Below 1 V
    T36-12 (3) - T19-1 (E1)
    1. Ignition switch ON
    2. Shift lever not in 3
    Below 1 V
    T36-11 (2) - T19-1 (E1)
    1. Ignition switch ON
    2. Shift lever not in 2 or L
    Below 1 V
    T36-10 (L) - T19-1 (E1)
    1. Ignition switch ON
    2. Shift lever not in L
    Below 1 V

    Text in Illustration 
    *1
    Component with harness connected
    (TCM)

    HINT:
    *: The voltage will drop slightly due to illumination of the back-up light.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM (Click here)  

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)
  1. Disconnect the T19 TCM connector.

  1. Disconnect the N1 park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T19-12 (NSW) - N1-4 (B)
    Always
    Below 1 Ω
    N1-4 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM (Click here)