DTC P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) |
| DTC Code | DTC Detection Condition | Trouble Area |
| P0705 | One of the following conditions is met: (A) Any 2 or more of the following signals are ON simultaneously (2-trip detection logic):
|
|

| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Neutral Position SW Signal | PNP Switch Status/ OFF or ON |
| When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. |
| Shift SW Status (R Range) | PNP Switch Status/ OFF or ON |
| When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. |
| Shift SW Status (D Range) | PNP Switch Status/ OFF or ON |
| When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. |
| Shift SW Status (2 Range) | PNP Switch Status/ OFF or ON |
| When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. |
| Shift SW Status (L Range) | PNP Switch Status/ OFF or ON |
| When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. |
| Shift SW Status (4 Range) | PNP Switch Status/ OFF or ON |
| When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. |
| Shift SW Status (3 Range) | PNP Switch Status/ OFF or ON |
| When the shift lever position displayed on the GTS differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. |
| 1.CHECK HARNESS AND CONNECTOR (ECU-IG&GAUGE FUSE - PARK/NEUTRAL POSITION SWITCH) |
![]() |
Disconnect the park/neutral position switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| N10-2 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| N10-2 (RB) - Body ground | Ignition switch off | Below 1 V |
| *1 | Front view of wire harness connector (to Park/Neutral Position Switch) |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE) |
Disconnect the C163 ECM connector.
![]() |
Disconnect the park/neutral position switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| N10-4 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| N10-4 (B) - Body ground | Ignition switch off | Below 1 V |
| *1 | Front view of wire harness connector (to Park/Neutral Position Switch) |
|
| ||||
| OK | |
| 3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Disconnect the park/neutral position switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 4 (B) - 5 (L) | Shift lever in P or N | Below 1 Ω |
| 2 (RB) - 1 (RL) | Shift lever in R | Below 1 Ω |
| 2 (RB) - 7 (DL) | Shift lever in D or 4 | Below 1 Ω |
| 2 (RB) - 3 (2L) | Shift lever in 3 | Below 1 Ω |
| 2 (RB) - 8 (LL) | Shift lever in 2 or L | Below 1 Ω |
| 4 (B) - 5 (L) | Shift lever not in P or N | 10 kΩ or higher |
| 2 (RB) - 1 (RL) | Shift lever not in R | 10 kΩ or higher |
| 2 (RB) - 7 (DL) | Shift lever not in D or 4 | 10 kΩ or higher |
| 2 (RB) - 3 (2L) | Shift lever not in 3 | 10 kΩ or higher |
| 2 (RB) - 8 (LL) | Shift lever not in 2 or L | 10 kΩ or higher |
| *1 | Component without harness connected (Park/Neutral Position Switch) |
|
| ||||
| OK | |
| 4.INSPECT TRANSMISSION CONTROL SWITCH |
![]() |
Disconnect the transmission control switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 9 (NSSD) - 3 (AT4) | Shift lever in D | 10 kΩ or higher |
| Shift lever in 4 | Below 1 Ω | |
| 10 (NSSL) - 4 (ATL) | Shift lever in 2 | 10 kΩ or higher |
| Shift lever in L | Below 1 Ω |
| *1 | Component without harness connected (Transmission Control Switch) |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TRANSMISSION CONTROL SWITCH) |
![]() |
Disconnect the transmission control switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| S30-9 (NSSD) - Body ground |
| 11 to 14 V |
| S30-9 (NSSD) - Body ground |
| Below 1 V |
| S30-10 (NSSL) - Body ground |
| 11 to 14 V |
| S30-10 (NSSL) - Body ground |
| Below 1 V |
| *1 | Front view of wire harness connector (to Transmission Control Switch) |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM) |
![]() |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| T36-9 (R) - T19-1 (E1) |
| 11 to 14 V* |
| T36-8 (D) - T19-1 (E1) |
| 11 to 14 V |
| T36-13 (4) - T19-1 (E1) |
| 11 to 14 V |
| T36-12 (3) - T19-1 (E1) |
| 11 to 14 V |
| T36-11 (2) - T19-1 (E1) |
| 11 to 14 V |
| T36-10 (L) - T19-1 (E1) |
| 11 to 14 V |
| T36-9 (R) - T19-1 (E1) |
| Below 1 V |
| T36-8 (D) - T19-1 (E1) |
| Below 1 V |
| T36-13 (4) - T19-1 (E1) |
| Below 1 V |
| T36-12 (3) - T19-1 (E1) |
| Below 1 V |
| T36-11 (2) - T19-1 (E1) |
| Below 1 V |
| T36-10 (L) - T19-1 (E1) |
| Below 1 V |
| *1 | Component with harness connected (TCM) |
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM) |
Disconnect the T19 TCM connector.
Disconnect the N10 park/neutral position switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T19-12 (NSW) - N10-4 (B) | Always | Below 1 Ω |
| N10-4 (B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||