Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM (w/ Jam Protection Function)

POWER WINDOW CONTROL SYSTEM (w/ Jam Protection Function) > Driver Side Power Window Manual Function does not Operate with Power Window Master Switch

for Preparation Click here


DESCRIPTION

If the manual UP / DOWN function does not operate, a malfunction may be present in the power window regulator master switch, power window regulator motor or wire harness.

WIRING DIAGRAM


B117121E09


INSPECTION PROCEDURE

1.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (BW, B VOLTAGE)


    B117126E39
  1. Disconnect the P6 master switch connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    P6-7 (BW) - Body ground
    Always
    10 to 14 V
    P6-6 (B) - Body ground
    Ignition switch ON
    10 to 14 V
    P6-6 (B) - Body ground
    Ignition switch OFF
    Below 1 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR (NO. 3 RELAY BLOCK - POWER WINDOW REGULATOR MASTER SWITCH)
OK


2.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY


    B117126E40
  1. Disconnect the P6 master switch connector.

  1. Using a service wire, connect the terminals according to the table below.

  1. Check operation of the power window regulator motor.

    OK:
    Tester Connection
    Specified Condition
    P6-4 (U) - P6-7 (BW)
    P6-9 (D) - Body ground
    Power window moves UP
    P6-4 (U) - Body ground
    P6-7 (BW) - P6-9 (D)
    Power window moves DOWN



OK
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
NG


3.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (DRIVER SWITCH)

B144123E01

  1. Remove the power window regulator master switch with its connectors still connected.

  1. Measure the voltage of the power window regulator master switch connector.

    Standard voltage:

    Tester Connection
    Switch Condition
    Specified Condition
    4(U) - 1 (E)
    Ignition switch ON, driver side power window switch OFF → UP (manual operation)
    Below 1 V → 10 to 14 V
    Ignition switch ON, driver side power window fully opened → driver side power window switch UP (AUTO operation) → driver side power window fully close
    Below 1 V → 10 to 14 V → Below 1 V
    9 (D) - 1 (E)
    Ignition switch ON, driver side power window switch OFF → DOWN (manual operation)
    Below 1 V → 10 to 14 V
    Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
    Below 1 V → 10 to 14 V → Below 1 V



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK


4.CHECK WIRE HARNESS (MASTER SWITCH - REGULATOR MOTOR (FOR DRIVER SIDE))

B117125E30

  1. Disconnect the P6 master switch connector.

  1. Disconnect the P7 motor connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    P6-9 (D) - P7-1
    Below 1 Ω
    P6-4 (U) - P7-2
    Below 1 Ω
    P6-9 (D) or P7-1 - Body ground
    10 kΩ or higher
    P6-4 (U) or P7-2 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY