Home › BRAKE › BRAKE › FRONT BRAKE (for TMT Made)

FRONT BRAKE (for TMT Made) > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.



1. INSTALL DISC BRAKE CYLINDER ASSEMBLY LH


F043121
  1. Install the cylinder with the 2 bolts.

    Torque:
    122 N*m{ 1244 kgf*cm , 90 ft.*lbf }



2. CONNECT FRONT NO. 1 WHEEL CYLINDER TUBE LH


F043120
  1. Using a union nut wrench, connect the tube to the cylinder.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



3. INSTALL FRONT ANTI-SQUEAL SHIM KIT


C194045E01
  1. Apply disc brake grease to both sides of each No. 1 shim.

  1. Install the No. 1 and No. 2 shims to each pad.

    NOTICE:
    1. When replacing worn pads, the shims must be replaced together with the pads.
    2. Install the shims in the correct position and direction.



4. INSTALL FRONT DISC BRAKE PAD
  1. Install the 2 disc brake pads to the cylinder.

    NOTICE:
    There should be no oil or grease on the friction surface of the pads and disc.



5. INSTALL FRONT DISC BRAKE ANTI-RATTLE SPRING
  1. for 15 inch Front Disc Brake:

    1. Install the 2 disc brake pad guide pins and pin hold clip.

      HINT:
      Install the spring together with the pin on the bottom side.

    2. Install the clip.



  1. for 16 inch Front Disc Brake:



      F043185E02
    1. Install the 2 pins and spring.

      HINT:
      Install the spring with the pin on the bottom side.



    2. F043185E01
    3. Install the 2 clips.

      NOTICE:
      When installing the clip, be sure to install the clip with the handle facing the vehicle center.



6. FILL RESERVOIR WITH BRAKE FLUID

Fluid:
SAE J1703 or FMVSS No. 116 DOT 3



7. BLEED AIR FROM MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.

  1. Remove the brake master cylinder reservoir filler cap assembly.

  1. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

  1. Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.



    C247712
  1. Slowly depress and hold the brake pedal.



    C247713
  1. Block the tube holes with your fingers, and then release the brake pedal.

  1. Remove your fingers, slowly depress and hold the brake pedal, block the tube holes with your fingers again, and then release the brake pedal. Repeat this step 3 or 4 times.

  1. Using a union nut wrench, connect the 2 brake tube to the brake master cylinder assembly.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



8. BLEED AIR FROM BRAKE LINE
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plugs.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    for front brake:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }
    for rear brake:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the cap.

  1. Bleed air from the brake line for each wheel by repeating the above procedures.



9. BLEED AIR FROM CLUTCH LINE (for Manual Transmission)
  1. Remove the brake master cylinder reservoir filler cap assembly.

  1. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the clutch line.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

  1. Remove the bleeder plug cap.



    C112661E08
  1. Connect a vinyl tube to the bleeder plug.

  1. Depress the clutch pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. At the point when fluid stops coming out, tighten the bleeder plug, and then release the clutch pedal.

  1. Repeat the previous 2 steps until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Install the bleeder plug cap.

  1. Check that all the air has been bled out of the clutch line.

  1. Check for brake fluid leaks.

  1. Check the brake fluid level in the reservoir.

    1. w/o VSC:

    2. w/ VSC:

  1. Install the brake master cylinder reservoir filler cap assembly.



10. CHECK BRAKE FLUID LEVEL IN RESERVOIR


F052092
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

    HINT:
    Add fluid to a level between the reservoir's MIN and MAX lines.



11. CHECK FOR BRAKE FLUID LEAKAGE


12. INSTALL FRONT WHEEL

Torque:
105 N*m{ 1071 kgf*cm , 77 ft.*lbf }