REAR BRAKE FLEXIBLE HOSE (w/o VSC) > INSTALLATION |
| 1. INSTALL REAR BRAKE TUBE FLEXIBLE HOSE |
![]() |
Attach a new clip to the flexible hose.
Connect the flexible hose to the 3-way.
Using a union nut wrench, connect the flexible hose to the brake tube while holding the flexible hose with a wrench.
| 2. FILL RESERVOIR WITH BRAKE FLUID |
| 3. FILL RESERVOIR WITH BRAKE FLUID (for TDV Made) |
| 4. FILL RESERVOIR WITH BRAKE FLUID (for TSAM Made) |
| 5. FILL RESERVOIR WITH BRAKE FLUID (for TMMIN Made) |
| 6. BLEED AIR FROM BRAKE MASTER CYLINDER (for TASA Made) |
Remove the brake master cylinder reservoir filler cap assembly.
Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.
Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.
![]() |
Slowly depress and hold the brake pedal.
![]() |
Block the tube holes with your fingers, and then release the brake pedal.
Remove the your fingers, slowly depress and hold the brake pedal, block the tube holes with your fingers again, and then release the brake pedal. Repeat this step 3 or 4 times.
Using a union nut wrench, connect the 2 brake tubes to the brake master cylinder assembly.
| 7. BLEED AIR FROM BRAKE MASTER CYLINDER (for TMT Made) |
Remove the brake master cylinder reservoir filler cap assembly.
Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.
Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.
![]() |
Slowly depress and hold the brake pedal.
![]() |
Block the tube holes with your fingers, and then release the brake pedal.
Remove your fingers, slowly depress and hold the brake pedal, block the tube holes with your fingers again, and then release the brake pedal. Repeat this step 3 or 4 times.
Using a union nut wrench, connect the 2 brake tube to the brake master cylinder assembly.
| 8. BLEED AIR FROM BRAKE MASTER CYLINDER (for TDV Made) |
Remove the brake master cylinder reservoir filler cap assembly.
Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.
Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.
![]() |
Slowly depress and hold the brake pedal.
![]() |
Cover the outer holes with your fingers, and release the pedal.
Repeat the 2 previous steps 3 or 4 times.
Using a union nut wrench, connect the 2 brake lines to the master cylinder.
| 9. BLEED AIR FROM BRAKE MASTER CYLINDER (for TSAM Made) |
Remove the brake master cylinder reservoir filler cap assembly.
Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.
Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.
![]() |
Slowly depress and hold the brake pedal.
![]() |
Block the tube holes with your fingers, and then release the brake pedal.
Remove the your fingers, slowly depress and hold the brake pedal, block the tube holes with your fingers again, and the n release the brake pedal. Repeat this step 3 or 4 times.
Using a union nut wrench, connect the 2 brake tubes to the brake master cylinder assembly.
| 10. BLEED AIR FROM BRAKE MASTER CYLINDER (for TMMIN Made) |
Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.
![]() |
Slowly depress and hold the brake pedal.
![]() |
Cover the outer holes with your finger, and release the pedal.
Repeat the 2 previous steps 3 or 4 times.
Using a union nut wrench, connect the 2 brake lines to the master cylinder.
| 11. BLEED AIR FROM BRAKE LINE |
Remove the bleeder plug cap.
Connect the vinyl tube to the bleeder plugs.
Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.
When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.
Repeat the 2 previous steps until all the air in the brake fluid is gone.
Tighten the bleeder plug.
Install the cap.
Bleed air from the brake line for each wheel by repeating the above procedures.
| 12. BLEED AIR FROM BRAKE LINE (for TDV Made) |
Remove the bleeder plug cap.
Connect the vinyl tube to the bleeder plugs.
Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.
When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.
Repeat the 2 previous steps until all the air in the brake fluid is gone.
Tighten the bleeder plug.
Install the cap.
Bleed air from the brake line for each wheel by repeating the above procedures.
| 13. BLEED AIR FROM BRAKE LINE (for TSAM Made) |
Remove the bleeder plug cap.
Connect the vinyl tube to the bleeder plugs.
Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.
When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.
Repeat the 2 previous steps until all the air in the brake fluid is gone.
Tighten the bleeder plug.
Install the cap.
Bleed air from the brake line for each wheel by repeating the above procedures.
| 14. BLEED AIR FROM BRAKE LINE (for TMMIN Made) |
Remove the bleeder plug cap.
Connect the vinyl tube to the bleeder plugs.
Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.
When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.
Repeat the 2 previous steps until all the air in the brake fluid is gone.
Tighten the bleeder plug.
Install the cap.
Bleed air from the brake line for each wheel by repeating the above procedures.
| 15. BLEED AIR FROM CLUTCH LINE (for Manual Transmission) |
Remove the brake master cylinder reservoir filler cap assembly.
Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the clutch line.
| Made | Fluid |
| except TSAM Made | SAE J1703 or FMVSS No. 116 DOT 3 |
| for TSAM Made | SAE J1704 or FMVSS No. 116 DOT 4 |
Remove the bleeder plug cap.
![]() |
Connect a vinyl tube to the bleeder plug.
Depress the clutch pedal several times, and then loosen the bleeder plug with the pedal depressed.
At the point when fluid stops coming out, tighten the bleeder plug, and then release the clutch pedal.
Repeat the previous 2 steps until all the air in the fluid is completely bled out.
Tighten the bleeder plug.
Install the bleeder plug cap.
Check that all the air has been bled out of the clutch line.
Check for brake fluid leaks.
Check the brake fluid level in the reservoir.
w/o VSC:
w/ VSC:
Install the brake master cylinder reservoir filler cap assembly.
| 16. CHECK BRAKE FLUID LEVEL IN RESERVOIR |
![]() |
Check the fluid level and add fluid if necessary.
| 17. CHECK BRAKE FLUID LEVEL IN RESERVOIR (for TDV Made) |
![]() |
Check the fluid level and add fluid if necessary.
| 18. CHECK BRAKE FLUID LEVEL IN RESERVOIR (for TSAM Made) |
![]() |
Check the fluid level and add fluid if necessary.
| 19. CHECK BRAKE FLUID LEVEL IN RESERVOIR (for TMMIN Made) |
![]() |
Check the fluid level.
If the brake fluid level is lower than the MIN line, check for leaks and inspect the disc brake pads. If necessary, refill the reservoir with brake fluid to the MAX line after repair or replacement.
| 20. CHECK FOR BRAKE FLUID LEAKAGE |