Home › BODY ELECTRICAL › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > CUSTOMIZE PARAMETERS

for Preparation Click here


HINT:
w/ Theft deterrent system:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function(s) can be customized.
  1. Be sure to write down the current settings before customizing.


Theft warning ECU  
Item
Default
Contents
Setting
Speed-sensitive automatic door lock function
ON*
Function that locks all doors once when vehicle speed reaches 25 km/h (16 mph)
ON/OFF
Ignition switch-linked automatic door unlock function
ON*
After speed-sensitive automatic door lock function operates, turning ignition switch OFF causes doors to automatically unlock
ON/OFF

HINT:
*: When customizing the ON/OFF setting of the speed-sensitive automatic door lock function and ignition switch-linked automatic door unlock function, please note that the 2 functions' settings are synchronized. For information on how to customize, refer to the flowchart on the following pages.


CUSTOMIZE METHOD FLOWCHART OF SPEED-SENSITIVE AUTOMATIC DOOR LOCK FUNCTION, IGNITION SWITCH-LINKED AUTOMATIC DOOR UNLOCK FUNCTION
  1. During customize mode, the alarm control functions are disabled.
  1. During customize mode, the following wireless control functions are disabled: remote alarm function, automatic locking function, operation stop function and illuminated entry function.
  1. In the flowchart, "lock operation" and "unlock operation" refer to wireless transmitter lock operation and unlock operation.
  1. During customize mode, the ECU will not output lock/unlock signals.
  1. At any time during customize mode, inserting the key into the key cylinder will end customize mode.


1.CHECK THAT THE FOLLOWING CONDITIONS ARE MET
  1. No key is in the ignition key cylinder.

  2. The theft deterrent system is in the disarmed state (when either condition below is met):

    1. - All the doors are in the unlocked condition and the doors are locked and unlocked using the transmitter.
    2. - The key is inserted into the ignition key cylinder, the ignition switch is turned ON then OFF, and then the key is removed.


NEXT


2.INSERT KEY AND PULL OUT KEY. REPEAT ONCE WITHIN 5 SECONDS.

    HINT:
    If the key is inserted into the ignition key cylinder and the ignition switch is turned ON, the customization mode will be canceled.


NEXT


3.WAIT FOR 5 SECONDS

    HINT:
    If the key is inserted into the ignition key cylinder without waiting 5 seconds, customization mode will be canceled.


NEXT


4.PRESS AND HOLD DOWN BOTH LOCK AND UNLOCK SWITCH
  1. Press and hold down both lock and unlock switches for over 3 seconds or more.

    NOTICE:
    Perform this procedure within 5 seconds of completing the previous step.

    HINT:
    When customize mode has been entered, the hazard warning lights will immediately flash once.


NEXT


5.PERFORM LOCK OPERATION
  1. Perform the lock operation 2 times within 2 seconds.

    NOTICE:
    Perform this procedure within 5 seconds of completing the previous step.

    HINT:
    If the lock operation is performed over 5 times or the unlock switch is pressed, customize mode will end.


NEXT


6.PERFORM UNLOCK OPERATION
  1. Perform the unlock operation once.

    NOTICE:
    Perform this procedure within 2 seconds of performing the last lock operation of the previous step.

    HINT:
    1. After the hazard warning lights flash 2 times, the user can confirm the customize setting, customize the setting, or end customize mode.

    1. A selection must be made within 10 seconds.


NEXT


7.SELECT CUSTOMIZE MODE SETTING

    Item
    Proceed to
    Check current setting
    A
    Turn ON speed-sensitive automatic door lock function and ignition switch-linked automatic door unlock function setting
    B
    Turn OFF speed-sensitive automatic door lock function and ignition switch-linked automatic door unlock function setting
    C
    End customize mode
    D


B.
Go to step 9

C.
Go to step 10

D.
Go to step 11
A


8.CHECK CURRENT SETTING
  1. Perform the unlock operation once.

  2. Result 
    Result
    Setting
    Hazard warning lights flash once
    ON
    Hazard warning lights flash twice
    OFF

    HINT:
    The current customize setting is communicated through hazard warning light flashes.


NEXT

END


9.TURN FUNCTION AND SETTING ON
  1. Perform the lock operation once. Then perform the unlock operation again within 2 seconds.

    HINT:
    The hazard warning lights will flash once.


NEXT

END


10.TURN FUNCTION AND SETTING OFF
  1. Perform the lock operation twice. Then perform the unlock operation again within 2 seconds.

    HINT:
    The hazard warning lights will flash twice.


NEXT

END


11.END CUSTOMIZE MODE
  1. Perform the lock operation 3 times ore more.


NEXT

END