Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM (w/ Secondary Air Injection System)

DTC    P0102    Mass Air Flow Circuit Low

DTC    P0103    Mass Air Flow Circuit High

for Preparation Click here


DESCRIPTION

The Mass Air Flow (MAF) meter measures the amount of air flowing through the throttle valve. The ECM uses this information to determine the fuel injection time and provide a proper air-fuel ratio. Inside the MAF meter, there is a heated platinum wire exposed to the flow of intake air.
By applying a specific current to the wire, the ECM heats this wire to a given temperature. The flow of incoming air cools the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to these components* in the MAF meter. The voltage level is proportional to the air flow through the sensor. The ECM interprets this voltage as the intake air amount.

HINT:
*: The circuit is constructed so that the platinum hot wire and temperature sensor provide a bridge circuit, with the power transistor controlled so that the potential of A and B remain equal to maintain the set temperature.
  1. When any of these DTCs are set, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM according to the engine RPM and throttle valve position. Fail-safe mode continues until a pass condition is detected.


A094565E04


DTC No.
DTC Detection Condition
Trouble Area
P0102
MAF meter circuit is open for more than 3 seconds
(1 trip detection logic)
  1. Open in MAF meter circuit
  2. MAF meter
  3. ECM
P0103
MAF meter circuit is shorted for more than 3 seconds
(1 trip detection logic)
  1. Short in MAF meter circuit
  2. MAF meter
  3. ECM

MONITOR DESCRIPTION

If there is a defect in the MAF meter or an open or short circuit, the voltage level will deviate from the normal operating range. The ECM interprets this deviation as a defect in the MAF meter and sets a DTC.
Example:
When the sensor output voltage is less than 0.2 V or more than 4.9 V and if either condition continues for more than 3 seconds, the ECM sets a DTC.
This monitor runs for 3 seconds (the first 3 seconds of engine idle) after the engine is started (1 trip detection logic).

HINT:
When DTC P0102 or P0103 is detected, check the airflow ratio by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / MAF.

Air Flow Value (g/sec.)
Malfunction
Approximately 0
  1. Open in MAF meter power source circuit
  2. Open or short in VG circuit
271.0 or more
Open in E2G circuit


WIRING DIAGRAM


A123739E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ DATA LIST (MASS AIR FLOW RATE)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

  1. Read the values.

    Result:
    Mass Air Flow Value (g/sec.)
    Proceed to
    Approximately 0.0
    A
    271.0 or more
    B
    Between 0.0 and 271.0*
    C

    HINT:
    *: The value must change when the throttle valve is opened or closed.



B
Go to step 6

C
CHECK FOR INTERMITTENT PROBLEMS
A


2.CHECK MASS AIR FLOW METER (POWER SOURCE)


    A054396E31
  1. Disconnect the A4 MAF meter connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    A4-1 (+B) - Body ground
    9 to 14 V



NG
Go to step 5
OK


3.CHECK ECM (VG VOLTAGE)


    A066060E89
  1. Start the engine.

  1. Measure the voltage of the ECM connector.

HINT:
The shift lever should be on P or N and the A/C switch should be turned OFF.

Standard voltage:
Tester Connection
Condition
Specified Condition
E10-28 (VG) - E10-30 (E2G)
Engine is idling
0.5 to 3.0 V



OK
REPLACE ECM
NG


4.CHECK WIRE HARNESS (MASS AIR FLOW METER - ECM)


    G034714E02
  1. Disconnect the A4 MAF meter connector.

  1. Disconnect the E10 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A4-3 (VG) - E10-28 (VG)
    Below 1 Ω
    A4-2 (E2G) - E10-30 (E2G)
    Below 1 Ω
    A4-3 (VG) or E10-28 (VG) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE MASS AIR FLOW METER 

5.CHECK WIRE HARNESS (MASS AIR FLOW METER - INTEGRATION RELAY (MAIN RELAY))


    G034715E01
  1. Disconnect the A4 MAF meter connector.

  1. Remove the integration relay from the engine room junction block.

  1. Disconnect the 1J integration relay connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A4-1 (+B) - 1J-5
    Below 1 Ω
    A4-1 (+B) or 1J-5 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

INSPECT ECM POWER SOURCE CIRCUIT 

6.CHECK ECM (SENSOR GROUND)


    A066060E90
  1. Measure the resistance of the E10 ECM connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E10-30 (E2G) - Body ground
    Below 1 Ω



NG
REPLACE ECM
OK


7.CHECK WIRE HARNESS (MASS AIR FLOW METER - ECM)


    G034714E03
  1. Disconnect the A4 MAF meter connector.

  1. Disconnect the E10 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A4-3 (VG) - E10-28 (VG)
    Below 1 Ω
    A4-2 (E2G) - E10-30 (E2G)
    Below 1 Ω
    A4-3 (VG) or E10-28 (VG) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE MASS AIR FLOW METER