DTC P0120 Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction |
DTC P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input |
DTC P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input |
DTC P0220 Throttle / Pedal Position Sensor / Switch "B" Circuit |
DTC P0222 Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input |
DTC P0223 Throttle / Pedal Position Sensor / Switch "B" Circuit High Input |
DTC P2135 Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation |

| DTC No. | DTC Detection Condition | Trouble Area |
| - | Conditions of DTC P0120, P0122, P0123, P0220, P0222 or P0223 continue for 2 seconds (open or short in throttle position sensor circuit) (1 trip detection logic) | - |
| P0120 | Output voltage of VTA1 quickly fluctuates up and down beyond upper and lower malfunction thresholds (1 trip detection logic) |
|
| P0122 | VTA1 is 0.2 V or less (1 trip detection logic) |
|
| P0123 | VTA1 is 4.535 V or more (1 trip detection logic) |
|
| P0220 | Output voltages of VTA1 and VTA2 quickly fluctuate beyond their respective upper and lower malfunction thresholds (1 trip detection logic) |
|
| P0222 | VTA2 is 1.75 V or less (1 trip detection logic) |
|
| P0223 | VTA2 is 4.8 V or more, VTA1 is between 0.2 and 2.02 V (1 trip detection logic) |
|
| P2135 | Condition (a) continues for 0.5 seconds or more, or condition (b) continues for 0.4 seconds or more (1 trip detection logic): (a) Difference between VTA1 and VTA2 is 0.02 V or less (b) VTA1 is 0.2 V or less and VTA2 is 1.75 V or less |
|
| Tester Display | Accelerator Pedal Fully Released | Accelerator Pedal Fully Depressed |
| Throttle Position | 10 to 22% | 66 to 98% |
| Throttle Position No. 2 | 2.1 to 3.1 V | 4.6 to 4.98 V |

| 1.READ DATA LIST (THROTTLE POS, THROTTLE POS NO. 2) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position and Throttle Position No. 2.
Read the values displayed on the intelligent tester.
| TP (VTA1) When AP Released | TP No. 2 (VTA2) When AP Released | TP (VTA1) When AP Depressed | TP No. 2 (VTA2) When AP Depressed | Suspected Area | Proceed to |
| 0% | 0 to 0.2 V | 0% | 0 to 0.2 V | VC circuit open | A |
| 100% | 4.6 to 4.98 V | 100% | 4.6 to 4.98 V | E2 circuit open | A |
| 0 or 100% | 2.1 to 3.1 V (Fail-safe) | 0 or 100% | 2.1 to 3.1 V (Fail-safe) | VTA1 circuit open or ground short | A |
| 10 to 22% (Fail-safe) | 0 to 0.2 V or 4.6 to 4.98 V | 10 to 22% (Fail-safe) | 0 to 0.2 V or 4.6 to 4.98 V | VTA2 circuit open or ground short | A |
| 10 to 22% | 2.1 to 3.1 V | 66 to 98% (Not fail-safe) | 4.6 to 4.98 V (Not fail-safe) | Throttle position sensor circuit is normal | B |
|
| ||||
| A | |
| 2.CHECK WIRE HARNESS (THROTTLE POSITION SENSOR - ECM) |
![]() |
Disconnect the T1 throttle body connector.
Disconnect the E11 ECM connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| T1-5 (VC) - E11-18 (VC) | Below 1 Ω |
| T1-6 (VTA) - E11-20 (VTA1) | Below 1 Ω |
| T1-4 (VTA2) - E11-19 (VTA2) | Below 1 Ω |
| T1-3 (E2) - E11-28 (E2) | Below 1 Ω |
| T1-5 (VC) or E11-18 (VC) - Body ground | 10 kΩ or higher |
| T1-6 (VTA) or E11-20 (VTA1) - Body ground | 10 kΩ or higher |
| T1-4 (VTA2) or E11-19 (VTA2) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK ECM (VC VOLTAGE) |
![]() |
Disconnect the T1 throttle body connector.
Turn the ignition switch ON.
Measure the voltage of the ECM connector.
| Tester Connection | Specified Condition |
| E11-18 (VC) - E11-28 (E2) | 4.5 to 5.0 V |
|
| ||||
| OK | |
| 4.REPLACE THROTTLE BODY ASSEMBLY |
| NEXT | |
| 5.CHECK IF DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS) |
Clear the DTCs.
Start the engine.
Idle the engine for 15 seconds or more.
Connect the intelligent tester to the DLC3.
Turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Check for DTCs.
| Display (DTC Output) | Proceed to |
| P0120, P0122, P0123, P0220, P0222, P0223 and/or P2135 | A |
| No output | B |
|
| ||||
| A | ||
| ||