Home › ENGINE ยท 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM (w/ Secondary Air Injection System)

DTC    P0016    Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)

for Preparation Click here


DESCRIPTION

Refer to DTCs P0335 and P0339 .

DTC No.
DTC Detection Condition
Trouble Area
P0016
Deviation in crankshaft position sensor signal and camshaft position signal (2 trip detection logic)
  1. Mechanical system (jumped tooth of timing chain or chain stretched)
  2. ECM

MONITOR DESCRIPTION

The ECM optimizes the valve timing using the VVT system to control the intake valve camshaft. The VVT system includes the ECM, Oil Control Valve (OCV) and VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal, applied to the OCV, regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake valve camshaft. The ECM calibrates the valve timing of the VVT system by setting the camshaft to the maximum retard angle when the engine is idling. The ECM closes the OCV to retard the cam. The ECM stores this value as VVT learned value. When the difference between the target valve timing and actual valve timing is more than 5°Crankshaft Angle (CA), the ECM learns it.
If the learned value meets conditions (a) and (b) below, the ECM interprets this as a defect in the VVT system and sets a DTC.
(a) VVT learning value is less than 20°CA or more than 39°CA.
(b) Above condition continues for 18 seconds or more.
This DTC shows that the camshaft was installed toward the crankshaft at an incorrect angle (for example: jumped tooth of timing belt).
This monitor runs after the engine is idling for 5 minutes.

WIRING DIAGRAM

Refer to DTCs P0335 and P0339 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0016 is output
    A
    P0016 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0016 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART
A


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)

HINT:
If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the A/C on.

  1. Turn the intelligent tester on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) / All Data / VVT Change Angle #1.

  1. Perform the Active Test. Check that the displacement angle varies.

    OK:
    Displacement angle varies.



NG
Go to step 4
OK


3.ADJUST VALVE TIMING
  1. Adjust the valve timing (Click here).



NEXT
Go to step 7

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
  1. Inspect the camshaft timing oil control valve assembly (Click here).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
OK


5.INSPECT OIL CONTROL VALVE FILTER
  1. Remove the oil control valve filter (Click here).

  1. Check that the filter is not clogged.

    OK:
    Filter is not clogged.



NG
CLEAN OR REPLACE OIL CONTROL VALVE FILTER
OK


6.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
  1. Replace the camshaft timing gear assembly (Click here).


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Read the output pending DTCs using the intelligent tester.

    OK:
    No pending DTC is output.



NG
GO TO DTC CHART
OK

END