Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM (w/ Secondary Air Injection System)

DTC    P0504    Brake Switch "A" / "B" Correlation

for Preparation Click here


DESCRIPTION

In this system, the signals of the stop light switch's duplex system (STP and ST1-) are used to judge whether the brake system is abnormal or not. When the signals of depressing and releasing the brake pedal are detected simultaneously, the ECM interprets this as a malfunction of the stop light switch.

Signal
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF

HINT:
The normal condition of the signals is shown in the table above.


DTC No.
DTC Detection Condition
Trouble Area
P0504
Conditions (a), (b) and (c) continue for 0.5 seconds or more:
(a) Ignition switch ON
(b) Brake pedal is released
(c) STP signal is OFF when ST1- signal is OFF
  1. Short in stop light switch signal circuit
  2. STOP fuse
  3. Stop light switch
  4. ECM

WIRING DIAGRAM


A120224E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK STOP LIGHT (OPERATION)
  1. Check that the stop lights turn on and off when the brake pedal is depressed and released, respectively.

OK:
Stop lights turn on and off when brake pedal is depressed and released, respectively.



NG
REPAIR OR REPLACE STOP LIGHT SWITCH CIRCUIT
OK


2.READ DATA LIST (STP SIGNAL, ST1 - VOLTAGE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light SW.

  1. Check the STP signal when depressing and releasing the brake pedal.

    OK:
    Brake Pedal Condition
    Specified Condition
    Depressed
    STP Signal ON
    Released
    STP Signal OFF



    A079135E06
  1. Measure the voltage of the ECM connectors.

    Standard voltage:
    Tester Connection
    Brake Pedal Condition
    Specified Condition
    E8-16 (ST1-) - E11-3 (E1)
    Depressed
    Below 1.5 V
    E8-16 (ST1-) - E11-3 (E1)
    Released
    7.5 to 14 V



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


3.INSPECT STOP LIGHT SWITCH ASSEMBLY


    A072924E07
  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pin not pushed
    Below 1 Ω
    3 - 4
    Pin not pushed
    10 kΩ or higher
    1 - 2
    Pin pushed
    10 kΩ or higher
    3 - 4
    Pin pushed
    Below 1 Ω



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


4.CHECK WIRE HARNESS (STOP LIGHT SWITCH - ECM)
G039269E02
  1. Disconnect the E8 and E9 ECM connectors.

  1. Disconnect the S14 stop light switch connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    S14-1 - E9-4 (STP)
    Below 1 Ω
    S14-4 - E8-16 (ST1-)
    Below 1 Ω
    S14-1 or E9-4 (STP) - Body ground
    10 kΩ or higher
    S14-4 or E8-16 (ST1-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM