Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM (w/ Secondary Air Injection System)

DTC    P2120    Throttle / Pedal Position Sensor / Switch "D" Circuit

DTC    P2122    Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input

DTC    P2123    Throttle / Pedal Position Sensor / Switch "D" Circuit High Input

DTC    P2125    Throttle / Pedal Position Sensor / Switch "E" Circuit

DTC    P2127    Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input

DTC    P2128    Throttle / Pedal Position Sensor / Switch "E" Circuit High Input

DTC    P2138    Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation

for Preparation Click here


DESCRIPTION

HINT:
  1. These DTCs are related to the accelerator pedal position sensor.
  2. This Electronic Throttle Control System (ETCS) does not use a throttle cable.
  3. This is the procedure for the accelerator pedal position sensor.

The Accelerator Pedal Position (APP) sensor is mounted on the accelerator pedal to detect the angle of the accelerator pedal. This sensor is electronically controlled and uses Hall-effect elements.
In the accelerator pedal position sensor, the voltage applied to the terminals VPA and VPA2 of the ECM changes between 0 and 5 V in proportion to the angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal angle and is used for engine control. VPA2 is used to detect malfunctions of the sensor itself.
The ECM monitors the accelerator pedal angle from VPA and VPA2 signal outputs, and controls the throttle motor based on these signals.

A255815E17


DTC No.
DTC Detection Condition
Trouble Area
P2120
VPA quickly fluctuates up and down beyond upper and lower malfunction thresholds for 0.5 seconds
(1 trip detection logic)
  1. Accelerator pedal position sensor
  2. ECM
P2122
Condition (a) continues for 0.5 seconds or more when accelerator pedal is fully released (1 trip detection logic):
(a) VPA is 0.4 V or less
  1. Accelerator pedal position sensor
  2. Open in VCPA circuit
  3. Open or ground short in VPA circuit
  4. ECM
P2123
Condition (a) continues for 2.0 seconds or more (1 trip detection logic):
(a) VPA is 4.8 V or more
  1. Accelerator pedal position sensor
  2. Open in EPA circuit
  3. ECM
P2125
Condition (a) continues for 0.5 seconds or more (1 trip detection logic):
(a) VPA2 quickly fluctuates up and down beyond upper and lower malfunction thresholds
  1. Accelerator pedal position sensor
  2. ECM
P2127
Condition (a) continues for 0.5 seconds or more when accelerator pedal is fully released (1 trip detection logic):
(a) VPA2 is 1.2 V or less
  1. Accelerator pedal position sensor
  2. Open in VCP2 circuit
  3. Open or ground short in VPA2 circuit
  4. ECM
P2128
Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic):
(a) VPA2 is 4.8 V or more
(b) VPA is 0.4 V or more and VPA is 3.45 V or less
  1. Accelerator pedal position sensor
  2. Open in EPA2 circuit
  3. ECM
P2138
Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic):
(a) Difference between VPA and VPA2 is 0.02 V or less
(b) VPA is 0.4 V or more and 1.2 V or less
  1. Short in VPA and VPA2 circuits
  2. Accelerator pedal position sensor
  3. ECM

HINT:
When DTC P2120, P2122, P2123, P2125, P2127, P2128 and/or P2138 is detected, check the output voltage of the accelerator pedal position sensor by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.

Suspected Area
Accel Pos No. 1
When AP Released
Accel Pos No. 2
When AP Released
Accel Pos No. 1
When AP Depressed
Accel Pos No. 2
When AP Depressed
VCP circuit open
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
Open or ground short in VPA circuit
0 to 0.2 V
1.2 to 2.0 V
0 to 0.2 V
3.4 to 4.75 V
Open or ground short in VPA2 circuit
0.5 to 1.1 V
0 to 0.2 V
2.6 to 4.5 V
0 to 0.2 V
EPA circuit open
4.5 to 5.5 V
4.5 to 5.5 V
4.5 to 5.5 V
4.5 to 5.5 V

HINT:
  1. The accelerator pedal position is expressed in terms of voltage.
  2. AP stands for accelerator pedal.


MONITOR DESCRIPTION

When either output voltage of VPA or VPA2 deviates from the standard range, or the difference between the output voltage of the two sensors is less than the threshold, the ECM concludes that there is a defect in the APP sensor. The ECM illuminates the MIL and sets a DTC.
Example:
The output voltage of the VPA is below 0.4 V or exceeds 4.8 V.
This monitor runs for 2 seconds (the first 2 seconds of engine idle) after the engine is started (1 trip detection logic).

FAIL-SAFE

The accelerator pedal position sensor has a main circuit and associated circuit. When one of the circuits is malfunctioning, APP is calculated by the output of the other circuit. When both of the circuits are malfunctioning, it is interpreted that the accelerator pedal is released. As a result, the throttle valve is closed and the engine idles.

WIRING DIAGRAM


A112573E07


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ DATA LIST (ACCELERATOR POSITION NO. 1, ACCELERATOR POSITION NO. 2)


    FI07052E10
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.

  1. Measure the voltage.

    Standard voltage:
    Accelerator Pedal
    Accelerator Position No. 1
    Accelerator Position No. 2
    Released
    0.5 to 1.1 V
    1.2 to 2.0 V
    Depressed
    2.6 to 4.5 V
    3.4 to 4.75 V



OK
Go to step 6
NG


2.CHECK ECM (VCPA, VCP2 VOLTAGE)


    A066060E95
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    E8-26 (VCPA) - E8-20 (EPA)
    4.5 to 5.0 V
    E8-27 (VCP2) - E8-21 (EPA2)
    4.5 to 5.0 V



NG
REPLACE ECM
OK


3.CHECK ECM (VPA, VPA2 VOLTAGE)


    A066060E96
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connector.

    Standard voltage:
    Tester Connection
    Accelerator Pedal Condition
    Specified Condition
    E8-18 (VPA) - E8-20 (EPA)
    Released
    0.5 to 1.1 V
    E8-18 (VPA) - E8-20 (EPA)
    Depressed
    2.5 to 4.6 V
    E8-19 (VPA2) - E8-21 (EPA2)
    Released
    1.5 to 2.9 V
    E8-19 (VPA2) - E8-21 (EPA2)
    Depressed
    3.5 to 5.0 V



OK
REPLACE ECM
NG


4.CHECK WIRE HARNESS (ACCELERATOR PEDAL POSITION SENSOR - ECM)


    G034948E02
  1. Disconnect the A22 accelerator pedal position sensor connector.

  1. Disconnect the E8 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A22-6 (VPA) - E8-18 (VPA)
    Below 1 Ω
    A22-5 (EPA) - E8-20 (EPA)
    Below 1 Ω
    A22-4 (VCPA) - E8-26 (VCPA)
    Below 1 Ω
    A22-3 (VPA2) - E8-19 (VPA2)
    Below 1 Ω
    A22-2 (EPA2) - E8-21 (EPA2)
    Below 1 Ω
    A22-1 (VCP2) - E8-27 (VCP2)
    Below 1 Ω
    A22-6 (VPA) or E8-18 (VPA) - Body ground
    10 kΩ or higher
    A22-5 (EPA) or E8-20 (EPA) - Body ground
    10 kΩ or higher
    A22-4 (VCPA) or E8-26 (VCPA) - Body ground
    10 kΩ or higher
    A22-3 (VPA2) or E8-19 (VPA2) - Body ground
    10 kΩ or higher
    A22-2 (EPA2) or E8-21 (EPA2) - Body ground
    10 kΩ or higher
    A22-1 (VCP2) or E8-27 (VCP2) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

NEXT


6.CHECK IF DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Clear the DTCs.

  1. Start the engine.

  1. Idle the engine for 15 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Check for DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P2120, P2122, P2123, P2125, P2127, P2128 and/or P2138
    A
    No output
    B



B
NORMAL
A

REPLACE ECM