Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM (w/ Secondary Air Injection System)

DTC    P2121    Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance

for Preparation Click here


DESCRIPTION

HINT:
This DTC is related to the accelerator pedal position sensor.

Refer to DTC P2120 .

DTC No.
DTC Detection Condition
Trouble Area
P2121
Either of following conditions 1 or 2 met for 0.5 seconds (1 trip detection logic)
  1. Difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V. (learned value of accelerator off position)
  2. Difference between VPA and VPA2 is greater than or equal to the specified value.
  1. Accelerator pedal position sensor circuit
  2. Accelerator pedal position sensor
  3. ECM

MONITOR DESCRIPTION

When the difference between the output voltages of VPA and VPA2 deviates from the standard, the ECM determines that the accelerator pedal position sensor is malfunctioning. The ECM turns on the MIL and stores the DTC.

FAIL-SAFE

The accelerator pedal position sensor has a main circuit and associated circuit. When and of the circuits is malfunctioning, APP is calculated by the output of the other circuit. When both of the circuits are malfunctioning, it is interpreted that the accelerator pedal is released. As a result, the throttle valve is closed and the engine idles.

WIRING DIAGRAM

Refer to DTC P2120 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ DATA LIST (ACCELERATOR POSITION NO. 1, ACCELERATOR POSITION NO. 2)


    FI07052E10
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.

  1. Measure the voltage.

    Standard voltage:
    Accelerator Pedal
    Accelerator Position No. 1
    Accelerator Position No. 2
    Released
    0.5 to 1.1 V
    1.2 to 2.0 V
    Depressed
    2.6 to 4.5 V
    3.4 to 5.0 V



OK
Go to step 4
NG


2.CHECK WIRE HARNESS (ACCELERATOR PEDAL POSITION SENSOR - ECM)


    G034948E02
  1. Disconnect the A22 accelerator pedal position sensor connector.

  1. Disconnect the E8 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A22-6 (VPA) - E8-18 (VPA)
    Below 1 Ω
    A22-5 (EPA) - E8-20 (EPA)
    Below 1 Ω
    A22-4 (VCPA) - E8-26 (VCPA)
    Below 1 Ω
    A22-3 (VPA2) - E8-19 (VPA2)
    Below 1 Ω
    A22-2 (EPA2) - E8-21 (EPA2)
    Below 1 Ω
    A22-1 (VCP2) - E8-27 (VCP2)
    Below 1 Ω
    A22-6 (VPA) or E8-18 (VPA) - Body ground
    10 kΩ or higher
    A22-5 (EPA) or E8-20 (EPA) - Body ground
    10 kΩ or higher
    A22-4 (VCPA) or E8-26 (VCPA) - Body ground
    10 kΩ or higher
    A22-3 (VPA2) or E8-19 (VPA2) - Body ground
    10 kΩ or higher
    A22-2 (EPA2) or E8-21 (EPA2) - Body ground
    10 kΩ or higher
    A22-1 (VCP2) or E8-27 (VCP2) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

NEXT


4.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Idle the engine for 15 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs (Click here).

    Result:

    Display (DTC Output)
    Proceed to
    P2120, P2122, P2123, P2125, P2127 and/or P2138
    A
    No output
    B



B
SYSTEM OK
A

REPLACE ECM