Home › ENGINE ยท 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM (w/ Secondary Air Injection System)

DTC    P0010    Camshaft Position "A" Actuator Circuit (Bank 1)

for Preparation Click here


DESCRIPTION

The Variable Valve Timing (VVT) system includes the ECM, Oil Control Valve (OCV) and VVT controller. The ECM sends a target "duty-cycle" control signal to the OCV. This control signal, applied to the OCV, regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed based on engine operation conditions such as intake air volume, throttle position and engine coolant temperature.
The ECM controls the OCV based on the signals from several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the OCV. As a result, the relative position between the camshaft and crankshaft is optimized, the engine torque and fuel economy improve, and the exhaust emission decreases. The ECM detects the actual valve timing using signals from the camshaft position sensor and crankshaft position sensor. The ECM performs feedback control and verifies target valve timing.

A103843E02


DTC No.
DTC Detection Condition
Suspected Area
P0010
Open or short in oil control valve circuit
(1 trip detection logic)
  1. Open or short in oil control valve circuit
  2. OCV
  3. ECM

MONITOR DESCRIPTION

After the ECM sends the "target" duty-cycle signal to the OCV, the ECM monitors the OCV current to establish an "actual" duty-cycle. The ECM detects a malfunction and sets a DTC when the actual duty-cycle ratio varies from the target duty-cycle ratio.
This monitor runs for 1 second (the first second of engine idle) after the engine is started.

WIRING DIAGRAM


A112564E02


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.PERFORM ACTIVE TEST (OPERATE OCV)
  1. Start and warm up the engine.

  1. Turn the ignition switch OFF.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / VVT Control (Bank 1).

  1. Using the intelligent tester, operate the OCV and check the engine speed.

    OK:
    Tester Operation
    Specified Condition
    OCV is OFF
    Normal engine speed
    OCV is ON
    Rough idle or engine stall



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


2.CHECK CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OCV SIGNAL)


    A094633E26
  1. Disconnect the C2 OCV connector.

  1. While idling the engine, check the waveform of the OCV connector using the oscilloscope.

    OK:
    Tester Connection
    Specified Condition
    C2-2 (OC1+) - C2-1 (OC1-)
    Correct waveform is as shown
    Tool Setting
    Condition
    5 V/DIV., 1 msec./DIV.
    Accelerate slowly after engine warm-up



OK
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
NG


3.CHECK ECM (OCV SIGNAL)


    G034684E05
  1. While idling the engine, check the waveform of the ECM connector using the oscilloscope.

    OK:
    Tester Connection
    Specified Condition
    E11-13 (OC1+) - E11-12 (OC1-)
    Correct waveform is as shown
    Tool Setting
    Condition
    5 V/DIV., 1 msec./DIV.
    Accelerate slowly after engine warm-up



NG
REPLACE ECM
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR