Home › ENGINE ยท 2TR-FBE › CHARGING › GENERATOR

GENERATOR > REASSEMBLY

for Preparation Click here



1. INSTALL GENERATOR DRIVE END FRAME BEARING


    A118448E03
  1. Using SST and a press, press in a new bearing.

    SST
    09950-60010   (09951-00470)
    09950-70010   (09951-07100)



    A118449E03
  1. Align the claws of the bearing retainer with the grooves inside the drive end frame.

  1. Install the bearing retainer with the 4 screws.

    Torque:
    2.3 N*m{ 23 kgf*cm , 20 in.*lbf }



2. INSTALL GENERATOR ROTOR ASSEMBLY
  1. Install the generator rotor to the drive end frame.

    NOTICE:
    Do not drop the generator rotor.

  1. Install the generator drive end frame space collar to the generator rotor.

  1. Install the washer to the generator rotor.



3. INSTALL GENERATOR COIL ASSEMBLY


    A118450E03
  1. Using a 21 mm deep socket wrench and press, slowly press in the generator coil assembly.

  1. Install the generator coil assembly with the 4 through bolts.

    Torque:
    5.9 N*m{ 60 kgf*cm , 52 in.*lbf }



4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY


    A118452E01
  1. While pushing the 2 brushes into the generator brush holder, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the brush holder hole.



    A118453E01
  1. Install the brush holder with the 2 screws.

    Torque:
    1.8 N*m{ 18 kgf*cm , 16 in.*lbf }

  1. Pull out the pin from the brush holder.



5. INSTALL TERMINAL INSULATOR


    A118454
  1. Install the terminal insulator.

    NOTICE:
    Make sure the terminal insulator is installed facing the proper direction.



6. INSTALL GENERATOR REAR END COVER
  1. Install the generator rear end cover with the 3 nuts.

    Torque:
    4.6 N*m{ 46 kgf*cm , 40 in.*lbf }



7. INSTALL GENERATOR PULLEY
  1. Mount the generator in a vise between aluminum plates.

  1. Install the pulley to the rotor shaft by tightening the generator pulley nut by hand.

  1. Install SST 1-A and 1-B to the rotor shaft.

    SST
    09820-63011   (09820-06010, 09820-06021)
    Item
    Part No.
    SST 1-A and 1-B
    09820-06010
    SST 2
    09820-06021



    A246527E01
  1. Hold SST 1-A with a torque wrench, and turn SST 1-B clockwise with the specified torque.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

    NOTICE:
    Make sure that the SST is secured to the rotor shaft.



    A203850E02
  1. Insert SST 2 to attach it to the pulley nut.



    A246523E01
  1. Tighten the pulley nut by turning SST 1-A in the direction shown in the illustration.

    Torque:
    111 N*m{ 1127 kgf*cm , 81 ft.*lbf }

  1. Remove SST 2 from the generator.



    A246528E01
  1. Turn SST 1-B in the direction shown in the illustration and remove SST 1-A and 1-B.

  1. Turn the pulley and check that the pulley moves smoothly.