Home › ENGINE ยท 1GR-FE › LUBRICATION › ENGINE OIL COOLER

ENGINE OIL COOLER > INSTALLATION

for Preparation Click here



1. INSTALL OIL FILTER BRACKET
  1. Install a new O-ring and the oil filter bracket with the 2 nuts and 3 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



2. INSTALL ENGINE OIL COOLER
  1. Clean the contact surfaces of the oil filter bracket and oil cooler.

  1. Place a new O-ring on the oil cooler.

  1. Apply a light coat of engine oil to the threads of the union bolt.



    A076453E01
  1. Install the oil cooler and plate washer with the union bolt.

    Torque:
    68 N*m{ 693 kgf*cm , 50 ft.*lbf }

  1. Connect the 2 hoses to the oil cooler.



3. INSTALL OIL FILTER


    A076324E01
  1. Check and clean the oil filter installation surface.

  1. Apply clean engine oil to the gasket of a new oil filter.

  1. Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.



    A076325E02
  1. Using SST, tighten the oil filter an additional 3/4 turn.

    SST
    09228-07501  
    If using a torque wrench to tighten the oil filter:

    Torque:
    18 N*m{ 183 kgf*cm , 13 ft.*lbf }



4. ADD ENGINE OIL
  1. Clean and install the oil drain plug with a new gasket.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



    A308107
  1. Add fresh engine oil.

    Standard capacity:
    Item
    Specified Condition
    Drain and refill with oil filter change
    5.5 liters (5.8 US qts, 4.8 Imp. qts)
    Drain and refill without oil filter change
    5.2 liters (5.5 US qts, 4.6 Imp. qts)
    Dry fill
    6.6 liters (7.0 US qts, 5.8 Imp. qts)

    NOTICE:
    Do not allow engine oil to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.

    If engine oil is on the location indicated by the arrow, replace the belt tensioner.

  1. Install the oil filler cap.



5. ADD ENGINE COOLANT
  1. Tighten all the plugs and fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plug

    Standard capacity:
    Item
    Specified Condition
    A/T
    9.8 liters (10.4 US qts, 8.6 Imp. qts)
    M/T
    8.5 liters (9.0 US qts, 7.5 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Please contact your TOYOTA dealer for further details.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Fill the radiator reservoir with TOYOTA Super Long Life Coolant (SLLC) to the F line.

  1. Install the radiator cap.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens.
      While the thermostat is open, circulate the coolant for several minutes.

    2. Maintain the engine speed at 2,500 to 3,000 rpm.

    3. Press the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When pressing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

  1. Stop the engine and wait until the coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A112081E01
  1. Check the coolant level in the radiator reservoir.
    If the coolant level is below the L line, add SLLC to the reservoir F line.



6. CHECK FOR ENGINE COOLANT LEAKS
  1. Check for engine coolant leaks .



7. INSTALL V-BANK COVER
  1. Install the V-bank cover with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }