Home › ENGINE ยท 1GR-FE › CHARGING › GENERATOR (for BOSCH Made)

GENERATOR (for BOSCH Made) > REASSEMBLY

for Preparation Click here



1. INSTALL GENERATOR DRIVE END FRAME BEARING


    A222320E01
  1. Using SST and a press, press in a new bearing.

    SST
    09950-60010   (09951-00520)
    09950-70010   (09951-07100)



    A222318
  1. Install the retainer plate with the 4 screws.

    Torque:
    3.1 N*m{ 35 kgf*cm , 30 in.*lbf }



2. INSTALL GENERATOR ROTOR ASSEMBLY

NOTICE:
Do not drop the generator rotor assembly.



    A196960E02
  1. Set the spacer ring, drive end frame, generator rotor assembly and SST1 to SST2 as shown in the illustration.

    SST
    09285-76010  
    09630-00014   (09631-00061)

  1. Using SST1, SST2 and a press, slowly press the generator rotor into the drive end frame and spacer ring.



3. INSTALL GENERATOR PULLEY
  1. Fix the generator in a vise between aluminum plates.

    NOTICE:
    Do not damage the generator.

  1. Temporarily install the washer and generator pulley with the nut.



    A225140E01
  1. Set SST, a ball joint lock nut wrench and an 8 mm bi-hexagon wrench as shown in the illustration.

    SST
    09820-30020  

  1. Hold the 8 mm bi-hexagon wrench in place and turn SST and the ball joint lock nut wrench clockwise to tighten the nut.

    Torque:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }

    NOTICE:
    1. Use the formula to calculate special torque values for situations where a ball joint lock nut wrench is combined with a torque wrench (Click here).
    2. Do not use a tool such as an impact wrench or equivalent.

  1. Check that the generator pulley rotates smoothly.



4. INSTALL FITTING RING


    A117274
  1. Align the 3 cutouts of the fitting ring with the stator generator with rectifier.



5. INSTALL GENERATOR STATOR SUB-ASSEMBLY WITH RECTIFIER
  1. Align the key of the drive end frame with the keyway of the generator stator.



    A117272
  1. Install the stator with the 4 bolts.

    Torque:
    4.3 N*m{ 44 kgf*cm , 38 in.*lbf }



6. INSTALL VOLTAGE REGULATOR SUB-ASSEMBLY WITH BRUSH


    A121957
  1. Attach the brushes and terminals to the rectifier end frame of the regulator.



  1. Install the regulator with the 3 screws.


    A121958E01

    Torque:
    for screw A:
    2.2 N*m{ 22 kgf*cm , 19 in.*lbf }
    for screw B:
    1.2 N*m{ 12 kgf*cm , 11 in.*lbf }

    HINT:
    Install screw B to the position shown in the illustration.



7. INSTALL GENERATOR REAR END COVER


    A117270E01
  1. Install the rear end cover with the 2 nuts and screw.

    Torque:
    for nut A:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }
    for nut B:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }
    for screw:
    2.4 N*m{ 24 kgf*cm , 21 in.*lbf }

    NOTICE:
    The protective tower must be attached on the end cover.



    A117269
  1. Install the 2 terminal covers by turning them clockwise.