DIFFERENTIAL SYSTEM (w/ Differential Lock) > INSPECTION |
| 1. INSPECT DIFFERENTIAL LOCK SYSTEM |
![]() |
Inspect the indicator light.
Check that the indicator light lights up for approximately 1 second when the ignition switch is turned to ON.
Inspect the differential lock operation.
Jack up the vehicle and start the engine.
Shift the transfer shift lever to the L position.
When the differential lock control switch is set to the ON position, the indicator light turns on. Differential lock is applied to the rear wheel at this time.
When the differential lock control switch is at the OFF position, the indicator light goes off. Differential lock is released for the rear wheel at this time.
![]() |
Check the voltage between the terminals of the four wheel drive control ECU when switching the differential control switch with the speedometer registering approximately 8 km/h (5 mph) or more.
| Switch Position | Terminal | Specified Condition |
| ON | 3 (M1) to 2 (M2) | 0.5 V or less (No change) |
| *a | ECU Side |
Return the differential lock control switch to OFF.
Stop the engine and lower the vehicle.
| 2. CHECK WIRE HARNESS AND CONNECTOR |
![]() |
Inspect the system circuit with the connector disconnected.
| *a | Wire Harness Side |
Disconnect the connector from the four wheel drive control ECU and inspect the connector on the wire harness side as shown in the table.
| Tester Connection | Trouble Part | Condition | Specified Condition |
| 3 (M1) - 2 (M2) | Rear differential lock actuator | - | Less than 100 Ω |
| 7 (GND) - Body ground | Body ground | - | Below 1 Ω |
| 10 (SPD) - Body ground | Speed sensor | Vehicle moves slowly | 1 pulse generation per 40 cm (15.75 in.) |
| 5 (IG) - Body ground | Differential fuse | Ignition switch ON | 10 to 14 V |
| 1 (RLP) - Body ground | Rear differential lock indicator switch | Ignition switch ON with indicator light ON | About 0 V |
| Ignition switch ON with indicator light OFF | 10 to 14 V | ||
| 8 (4WD) - Body ground | L position switch | Ignition switch ON with transfer shift lever not in L | About 0 V |
| Ignition switch ON with transfer shift lever in L | 10 to 14 V | ||
| 4 (R) - Body ground | Differential lock control switch | Ignition switch ON with differential lock control switch ON | 10 to 14 V |
| Ignition switch ON with differential lock control switch OFF | About 0 V |
| 3. CHECK FOUR WHEEL DRIVE CONTROL ECU NO. 2 |
![]() |
Inspect the system circuit with the connector connected.
Turn the ignition switch to ON.
Shift the transfer shift lever to the L position.
Using a voltmeter, measure the voltage when the differential lock control switch is in the position shown in the table.
| Tester Connection | Switch Position | Specified Condition |
| 8 (4WD) - 7 (GND) | - | 0.5 V or less |
| 1 (RLP) - 7 (GND) | ON* | 0.5 V or less |
| 3 (M1) - 2 (M2) | OFF → ON | 0.5 V or less → 10 to 14 V (approx. 1 sec.) → 0.5 V or less |
| 2 (M2) - 3 (M1) | ON → OFF |
| *a | ECU Side |
Install the ECU.
| 4. INSPECT DIFFERENTIAL LOCK COMPONENTS |
Inspect the relay operation.
Jack up the vehicle.
Use a heater main relay and connect it as shown below.
Rotate the tire and check that the differential lock has occurred.

| *1 | Heater Main Relay | - | - |
| *a | Free → Lock | *b | Lock → Free |
| 5. INSPECT DIFFERENTIAL LOCK SWITCH |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 3 - 4 | OFF | 10 kΩ or higher |
| ON | Below 1 Ω |
| *a | Component without harness connected (Differential Lock Switch) |
| 6. INSPECT NO. 4 TRANSFER INDICATOR SWITCH |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 2 - 1 | Pushed | Below 1 Ω |
| Not pushed | 100 kΩ or higher |
| *a | Component without harness connected (No. 4 Transfer Indicator Switch) |