1KD-FTV STARTING > SERVICE DATA |
| for 2.2 kW Type Bosch made | Starter | No-load characteristics current | 123A or less at 11.5 V |
| Starter armature assembly | Maximum circle runout | 0.04 mm (0.0016 in.) | |
| Standard circle runout | 0.02 mm (0.0008 in.) | ||
| Standard commutator diameter | 32.2 mm (1.2783 in.) | ||
| Minimum commutator diameter | 31.1 mm (1.2347 in.) | ||
| Standard undercut depth | 0.9 mm (0.0354 in.) | ||
| Minimum undercut depth | 0.4 mm (0.0157 in.) | ||
| Segments | Below 1.7 Ω | ||
| Segment - Coil core | 10 kΩ or higher | ||
| Brush | Standard length | 14.0 mm (0.5558 in.) | |
| Minimum length | 9.0 mm (0.3543 in. ) | ||
| Tester connection A-B | 10 kΩ or higher | ||
| Tester connection A-C | 10 kΩ or higher | ||
| Tester connection A-D | Below 1 Ω | ||
| Tester connection B-C | Below 1 Ω | ||
| Tester connection B-D | 10 kΩ or higher | ||
| Tester connection C-D | 10 kΩ or higher | ||
| Magnet starter switch | Terminal 50 - Terminal C | Below 1 Ω | |
| Terminal 50 - Body | Below 2 Ω | ||
| for 2.2 kW Type Denso made | Starter | No-load characteristics current | 120 A or less at 11.5 V |
| Starter armature | Maximum circle runout | 0.05 mm (0.0020 in.) | |
| Standard commutator diameter | 35.5 mm (1.378 in.) | ||
| Minimum commutator diameter | 34.0 mm (1.339 in.) | ||
| Standard undercut depth | 0.7 mm (0.028 in.) | ||
| Minimum undercut depth | 0.2 mm (0.008 in.) | ||
| Segments | Below 1 Ω | ||
| Segment - Coil core | 10 kΩ or higher | ||
| Brush length | Standard length | 16.5 mm (0.650 in.) | |
| Minimum length | 9.0 mm (0.354 in. ) | ||
| Brush spring | Standard spring installed load | 26.5 to 32.3 N (2.7 to 3.3 kgf*cm, 5.9 to 7.3 in.*lbf) | |
| Minimum spring installed load | 17.6 N (1.8 kgf*cm, 4.0 in.*lbf) | ||
| Brush holder | Positive brush - Negative brush | 10 kΩ or higher | |
| Magnet starter switch | Terminal 50 - Terminal C | Below 1 Ω | |
| Terminal 50 - Body | Below 2 Ω | ||
| Glow plug | Resistance | Approx. 0.95 Ω | |
| ECT sensor | Resistance | Approx. 20°C (68°F) 2.32 to 2.59 kΩ | |
| Approx. 80°C (176°F) 0.310 to 0.326 kΩ | |||
| Starter relay | Specified resistance 3-5 | 10 kΩ or higher | |
| Below 1 Ω (when battery voltage is applied to terminal 1 and 2) | |||
| Glow relay | Specified resistance 3-5 | 10 kΩ or higher | |
| Below 1 Ω (when battery voltage is applied to terminal 1 and 2) | |||
| Ignition switch | Tester connection - | Switch condition Lock | Specified condition 10 kΩ or higher |
| Tester connection 2 (ACC) - 4 (AM1) | Switch condition ACC | Specified condition Below 1 Ω | |
| Tester connection 1 (IG1) - 4 (AM1) 2 (ACC) - 4 (AM1) 5 (AM2) - 6 (IG2) | Switch condition ON | Specified condition Below 1 Ω | |
| Tester connection 1 (IG1) - 4 (AM1) 3 (ST1) - 4 (AM1) 5 (AM2) - 6 (IG2) 5 (AM2) - 7 (ST2) | Switch condition START | Specified condition Below 1 Ω | |