Home › BRAKE › BRAKE › LOAD SENSING PROPORTIONING VALVE (w/o VSC)

LOAD SENSING PROPORTIONING VALVE (w/o VSC) > REPLACEMENT

for Preparation Click here



1. DRAIN BRAKE FLUID

NOTICE:
Wash off brake fluid immediately if it comes in contact with any painted surface.



2. REMOVE LOAD SENSING PROPORTIONING VALVE ASSEMBLY


    F052096
  1. Using a union nut wrench, disconnect the 3 brake lines from the valve.

  1. Remove the lock nut.



    F052097
  1. Remove the 2 bolts and valve.



3. INSTALL LOAD SENSING PROPORTIONING VALVE ASSEMBLY


    F052097
  1. Install the valve with the 2 bolts.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

  1. Install the valve with the 2 bolts.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }



    F052096
  1. Using a union nut wrench, connect the 3 brake lines to the valve.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



4. FILL RESERVOIR WITH BRAKE FLUID

Fluid:
SAE J1703 or FMVSS No. 116 DOT 3



5. FILL RESERVOIR WITH BRAKE FLUID (for TDV Made)

Fluid:
SAE J1703 or FMVSS No. 116 DOT 3



6. FILL RESERVOIR WITH BRAKE FLUID (for TSAM Made)

Fluid:
SAE J1704 or FMVSS No. 116 DOT 4



7. FILL RESERVOIR WITH BRAKE FLUID (for TMMIN Made)

Fluid :
SAE J1703 or FMVSS No. 116 DOT 3



8. BLEED AIR FROM BRAKE MASTER CYLINDER (for TASA Made)

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.

  1. Remove the brake master cylinder reservoir filler cap assembly.

  1. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

    Fluid:
    SAE J1709 or FMVSS No. 116 DOT3

  1. Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.



    C122638
  1. Slowly depress and hold the brake pedal.



    C122639
  1. Block the tube holes with your fingers, and then release the brake pedal.

  1. Remove the your fingers, slowly depress and hold the brake pedal, block the tube holes with your fingers again, and then release the brake pedal. Repeat this step 3 or 4 times.

  1. Using a union nut wrench, connect the 2 brake tubes to the brake master cylinder assembly.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



9. BLEED AIR FROM BRAKE MASTER CYLINDER (for TMT Made)

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.

  1. Remove the brake master cylinder reservoir filler cap assembly.

  1. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

  1. Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.



    C247712
  1. Slowly depress and hold the brake pedal.



    C247713
  1. Block the tube holes with your fingers, and then release the brake pedal.

  1. Remove your fingers, slowly depress and hold the brake pedal, block the tube holes with your fingers again, and then release the brake pedal. Repeat this step 3 or 4 times.

  1. Using a union nut wrench, connect the 2 brake tube to the brake master cylinder assembly.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



10. BLEED AIR FROM BRAKE MASTER CYLINDER (for TDV Made)

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.

  1. Remove the brake master cylinder reservoir filler cap assembly.

  1. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT 3

  1. Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.



    C247712
  1. Slowly depress and hold the brake pedal.



    C247713
  1. Cover the outer holes with your fingers, and release the pedal.

  1. Repeat the 2 previous steps 3 or 4 times.

  1. Using a union nut wrench, connect the 2 brake lines to the master cylinder.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



11. BLEED AIR FROM BRAKE MASTER CYLINDER (for TSAM Made)

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.

  1. Remove the brake master cylinder reservoir filler cap assembly.

  1. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

    Fluid:
    SAE J1704 or FMVSS No. 116 DOT 4

  1. Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.



    C247712
  1. Slowly depress and hold the brake pedal.



    C247713
  1. Block the tube holes with your fingers, and then release the brake pedal.

  1. Remove the your fingers, slowly depress and hold the brake pedal, block the tube holes with your fingers again, and the n release the brake pedal. Repeat this step 3 or 4 times.

  1. Using a union nut wrench, connect the 2 brake tubes to the brake master cylinder assembly.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



12. BLEED AIR FROM BRAKE MASTER CYLINDER (for TMMIN Made)

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.

  1. Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.



    C247712
  1. Slowly depress and hold the brake pedal.



    C247713
  1. Cover the outer holes with your finger, and release the pedal.

  1. Repeat the 2 previous steps 3 or 4 times.

  1. Using a union nut wrench, connect the 2 brake lines to the master cylinder.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



13. BLEED AIR FROM LOAD SENSING VALVE BODY
  1. Remove the bleeder plug cap.



    C184294
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 107 kgf*cm , 8 ft.*lbf }

  1. Install the bleeder plug cap.



14. BLEED AIR FROM LOAD SENSING VALVE BODY (for TDV Made)
  1. Remove the bleeder plug cap.



    C184294
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 107 kgf*cm , 8 ft.*lbf }

  1. Install the bleeder plug cap.



15. BLEED AIR FROM LOAD SENSING VALVE BODY (for TSAM Made)
  1. Remove the bleeder plug cap.



    C184294
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 107 kgf*cm , 8 ft.*lbf }

  1. Install the bleeder plug cap.



16. BLEED AIR FROM LOAD SENSING VALVE BODY (for TMMIN Made)
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plug.



    C184294
  1. Depress the pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 107 kgf*cm , 8 ft.*lbf }

  1. Install the bleeder plug cap.



17. BLEED AIR FROM BRAKE LINE
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plugs.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    for front brake:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }
    for rear brake:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the cap.

  1. Bleed air from the brake line for each wheel by repeating the above procedures.



18. BLEED AIR FROM BRAKE LINE (for TDV Made)
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plugs.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    for front brake:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }
    for rear brake:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the cap.

  1. Bleed air from the brake line for each wheel by repeating the above procedures.



19. BLEED AIR FROM BRAKE LINE (for TSAM Made)
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plugs.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    for front brake:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }
    for rear brake:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the cap.

  1. Bleed air from the brake line for each wheel by repeating the above procedures.



20. BLEED AIR FROM BRAKE LINE (for TMMIN Made)
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plugs.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    for front brake:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }
    for rear brake:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the cap.

  1. Bleed air from the brake line for each wheel by repeating the above procedures.



21. BLEED AIR FROM CLUTCH LINE (for Manual Transmission)
  1. Remove the brake master cylinder reservoir filler cap assembly.

  1. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the clutch line.

    Fluid:
    Made
    Fluid
    except TSAM Made
    SAE J1703 or FMVSS No. 116 DOT 3
    for TSAM Made
    SAE J1704 or FMVSS No. 116 DOT 4

  1. Remove the bleeder plug cap.



    C112661E08
  1. Connect a vinyl tube to the bleeder plug.

  1. Depress the clutch pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. At the point when fluid stops coming out, tighten the bleeder plug, and then release the clutch pedal.

  1. Repeat the previous 2 steps until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Install the bleeder plug cap.

  1. Check that all the air has been bled out of the clutch line.

  1. Check for brake fluid leaks.

  1. Check the brake fluid level in the reservoir.

    1. w/o VSC:

    2. w/ VSC:

  1. Install the brake master cylinder reservoir filler cap assembly.



22. CHECK BRAKE FLUID LEVEL IN RESERVOIR


F052092
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

    HINT:
    Add fluid to a level between the reservoir's MIN and MAX lines.



23. CHECK BRAKE FLUID LEVEL IN RESERVOIR (for TDV Made)


    F052092
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT 3

    HINT:
    Add fluid to a level between the reservoir's MIN and MAX lines.



24. CHECK BRAKE FLUID LEVEL IN RESERVOIR (for TSAM Made)


    F052092
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1704 or FMVSS No. 116 DOT 4

    HINT:
    Add fluid to a level between the reservoir's MIN and MAX lines.



25. CHECK BRAKE FLUID LEVEL IN RESERVOIR (for TMMIN Made)


    F052092
  1. Check the fluid level.
    If the brake fluid level is lower than the MIN line, check for leaks and inspect the disc brake pads. If necessary, refill the reservoir with brake fluid to the MAX line after repair or replacement.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT 3



26. CHECK FOR BRAKE FLUID LEAKAGE