Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)

AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) > Speaker Circuit

for Preparation Click here


DESCRIPTION

The radio receiver assembly sends sound signals to the speakers.

WIRING DIAGRAM


C245516E02


INSPECTION PROCEDURE

1.CHECK SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Malfunction in front speaker area
    A
    Malfunction in rear speaker area
    B



B
Go to step 4
A


2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E178457
  1. Disconnect the S16*1 and/or S15*2 front No. 1 speaker connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    4 Ω



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - FRONT NO. 1 SPEAKER)
  1. Disconnect the R2 radio receiver assembly connector.

  1. Disconnect the S16*1 and/or S15*2 front No. 1 speaker connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    R2-1 (FR+) - S16-1
    Always
    Below 1 Ω
    R2-5 (FR-) - S16-2
    R2-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    R2-5 (FR-) - Body ground
    for LH 
    Tester Connection
    Condition
    Specified Condition
    R2-2 (FL+) - S15-1
    Always
    Below 1 Ω
    R2-6 (FL-) - S15-2
    R2-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    R2-6 (FL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO RECEIVER ASSEMBLY (Click here)  

4.INSPECT REAR SPEAKER ASSEMBLY


    E178457
  1. Disconnect the S18*1 and/or S17*2 rear speaker connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    4 Ω



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - REAR SPEAKER)
  1. Disconnect the R3 radio receiver assembly connector.

  1. Disconnect the S18*1 and/or S17*2 rear speaker connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    R3-1 (RR+) - S18-1
    Always
    Below 1 Ω
    R3-3 (RR-) - S18-2
    R3-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    R3-3 (RR-) - Body ground
    for LH 
    Tester Connection
    Condition
    Specified Condition
    R3-2 (RL+) - S17-1
    Always
    Below 1 Ω
    R3-6 (RL-) - S17-2
    R3-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    R3-6 (RL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO RECEIVER ASSEMBLY (Click here)