Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM

NAVIGATION SYSTEM > Speaker Circuit


DESCRIPTION

The navigation receiver assembly sends sound signals to the speakers.

WIRING DIAGRAM


C240170E29


INSPECTION PROCEDURE

1.CHECK SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Malfunction in front speaker area
    A
    Malfunction in rear speaker area
    B



B
Go to step 7
A


2.CHECK FRONT SIDE SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Front No. 2 speaker assembly
    A
    Front No. 1 speaker assembly
    B



B
Go to step 5
A


3.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY
  1. Temporarily replace the front No. 2 speaker with a new or normally functioning one (Click here).

  1. Check that the malfunction disappears.

    HINT:
    1. Connect all the speaker connectors to the speakers.
    2. When there is a possibility that either the right or left speaker is defective, inspect by interchanging the right one with the left one.

    Result 
    Result
    Proceed to
    Malfunction disappears
    A
    Malfunction does not disappear
    B



B
Go to step 4
A

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)
  1. Disconnect the N8 navigation receiver assembly connector.

  1. Disconnect the T25*1 and/or T24*2 front No. 2 speaker connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    N8-1 (FR+) - T25-4 (TWR+)
    Always
    Below 1 Ω
    N8-5 (FR-) - T25-2 (TWR-)
    N8-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    N8-5 (FR-) - Body ground
    for LH 
    Tester Connection
    Condition
    Specified Condition
    N8-2 (FL+) - T24-4 (TWL+)
    Always
    Below 1 Ω
    N8-6 (FL-) - T24-2 (TWL-)
    N8-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    N8-6 (FL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)  

5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E178457
  1. Disconnect the S16*1 and/or S15*2 front No. 1 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    4 Ω



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)
  1. *1: for RH
  2. *2: for LH
  1. Disconnect the T25*1 and/or T24*2 front No. 2 speaker assembly connector.

  1. Disconnect the S16*1 and/or S15*2 front No. 1 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    T25-3 (+) - S16-1
    Always
    Below 1 Ω
    T25-1 (-) - S16-2
    T25-3 (+) - Body ground
    Always
    10 kΩ or higher
    T25-1 (-) - Body ground
    for LH 
    Tester Connection
    Condition
    Specified Condition
    T24-3 (+) - S15-1
    Always
    Below 1 Ω
    T24-1 (-) - S15-2
    T24-3 (+) - Body ground
    Always
    10 kΩ or higher
    T24-1 (-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)  

7.INSPECT REAR SPEAKER ASSEMBLY


    E178457
  1. Disconnect the S18*1 and/or S17*2 rear speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    4 Ω



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY)
  1. Disconnect the N7 navigation receiver assembly connector.

  1. Disconnect the S18*1 and/or S17*2 rear speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    N7-1 (RR+) - S18-1
    Always
    Below 1 Ω
    N7-3 (RR-) - S18-2
    N7-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    N7-3 (RR-) - Body ground
    for LH 
    Tester Connection
    Condition
    Specified Condition
    N7-2 (RL+) - S17-1
    Always
    Below 1 Ω
    N7-6 (RL-) - S17-2
    N7-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    N7-6 (RL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)