Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)

AUDIO AND VISUAL SYSTEM (for Radio and Display Type) > Speaker Circuit

for Preparation Click here


DESCRIPTION

The radio and display receiver assembly sends sound signals to the speakers.

WIRING DIAGRAM


C240170E23


INSPECTION PROCEDURE

1.CHECK SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Malfunction in front speaker area
    A
    Malfunction in rear speaker area
    B



B
Go to step 7
A


2.CHECK FRONT SIDE SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Front No. 2 speaker assembly
    A
    Front No. 1 speaker assembly
    B



B
Go to step 5
A


3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
  1. Temporarily replace the front No. 2 speaker with a new or normally functioning one (Click here).

  1. Check that the malfunction disappears.

    HINT:
    1. Connect all the speaker connectors to the speakers.
    2. When there is a possibility that either the right or left speaker is defective, inspect by interchanging the right one with the left one.

    Result 
    Result
    Proceed to
    Malfunction disappears
    A
    Malfunction does not disappear
    B



B
Go to step 4
A

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - FRONT NO. 2 SPEAKER)
  1. Disconnect the R20 radio and display receiver assembly connector.

  1. Disconnect the T25*1 and/or T24*2 front No. 2 speaker connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    R20-1 (FR+) - T25-4
    Always
    Below 1 Ω
    R20-5 (FR-) - T25-2
    R20-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    R20-5 (FR-) - Body ground
    for LH 
    Tester Connection
    Condition
    Specified Condition
    R20-2 (FL+) - T24-4
    Always
    Below 1 Ω
    R20-6 (FL-) - T24-2
    R20-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    R20-6 (FL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)  

5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E178457
  1. Disconnect the S16*1 and/or S15*2 front No. 1 speaker connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    4 Ω



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 1 SPEAKER)
  1. *1: for RH
  2. *2: for LH
  1. Disconnect the T25*1 and/or T24*2 front No. 2 speaker connector.

  1. Disconnect the S16*1 and/or S15*2 front No. 1 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    T25-3 - S16-1
    Always
    Below 1 Ω
    T25-1 - S16-2
    T25-3 - Body ground
    Always
    10 kΩ or higher
    T25-1 - Body ground
    for LH 
    Tester Connection
    Condition
    Specified Condition
    T24-3 - S15-1
    Always
    Below 1 Ω
    T24-1 - S15-2
    T24-3 - Body ground
    Always
    10 kΩ or higher
    T24-1 - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)  

7.INSPECT REAR SPEAKER ASSEMBLY


    E178457
  1. Disconnect the S18*1 and/or S17*2 rear speaker connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    4 Ω



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - REAR SPEAKER)
  1. Disconnect the R19 radio and display receiver assembly connector.

  1. Disconnect the S18*1 and/or S17*2 rear speaker connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    R19-1 (RR+) - S18-1
    Always
    Below 1 Ω
    R19-3 (RR-) - S18-2
    R19-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    R19-3 (RR-) - Body ground
    for LH 
    Tester Connection
    Condition
    Specified Condition
    R19-2 (RL+) - S17-1
    Always
    Below 1 Ω
    R19-6 (RL-) - S17-2
    R19-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    R19-6 (RL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)