Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM (for Navigation Receiver Type)

REAR VIEW MONITOR SYSTEM (for Navigation Receiver Type) > Display Signal Circuit between Navigation Receiver Assembly and Television Camera Assembly

for Preparation Click here


DESCRIPTION

This is the display signal circuit between the navigation receiver assembly and the rear television camera assembly.

WIRING DIAGRAM


E224828E11


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
  1. Disconnect the N6 navigation receiver assembly connector.

  1. Disconnect the T38 rear television camera assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N6-7 (CA+) - T38-4 (CB+)
    Always
    Below 1 Ω
    N6-8 (V+) - T38-2 (CV+)
    Always
    Below 1 Ω
    N6-15 (CGND) - T38-3 (CGND)
    Always
    Below 1 Ω
    N6-16 (V-) - T38-1 (CV-)
    Always
    Below 1 Ω
    N6-7 (CA+) - Body ground
    Always
    10 kΩ or higher
    N6-8 (V+) - Body ground
    Always
    10 kΩ or higher
    N6-15 (CGND) - Body ground
    Always
    10 kΩ or higher
    N6-16 (V-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK NAVIGATION RECEIVER ASSEMBLY


    E224536E11
  1. Disconnect the N6 navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N6-15 (CGND) - Body ground
    Always
    Below 1 Ω
    N6-16 (V-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Navigation Receiver Assembly)



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


3.CHECK NAVIGATION RECEIVER ASSEMBLY


    E227664E19
  1. Disconnect the T38 rear television camera assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    T38-4 (CB+) - T38-3 (CGND)
    Ignition switch ON, shift lever in R
    5.5 to 7.05 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Rear Television Camera Assembly)



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


4.CHECK REAR TELEVISION CAMERA ASSEMBLY


  1. Using an oscilloscope, check the waveform.


    E224537E09


    Text in Illustration 
    *a
    Component with harness connected
    (Navigation Receiver Assembly)
    *b
    Waveform 1
    *c
    Waveform 2
    *d
    Synchronization Signal
    *e
    Video Waveform
    -
    -
    Measurement Condition 
    Item
    Content
    Tester Connection
    N6-8(V+) - N6-16 (V-)
    Tool Setting
    0.2 V/DIV., 50 μs/DIV.
    Condition
    1. Waveform 1: Ignition switch ON, shift lever in R
    2. Waveform 2: Ignition switch ON, shift lever in R, screen blacked out by covering camera lens

    OK:
    Waveform is as shown in illustration.

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.



NG
REPLACE REAR TELEVISION CAMERA ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)