DTC P1603 Engine Stall History |
DTC P1605 Rough Idling |
| DTC No. | DTC Detection Condition | Trouble Area |
| P1603 | After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the engine, with the engine running, the engine stops (the engine speed drops to 200 rpm or less) without the engine switch being operated for 0.5 seconds or more (1 trip detection logic). |
|
| DTC No. | DTC Detection Condition | Trouble Area |
| P1605 | After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to 400 rpm or less (1 trip detection logic). |
|
| Symptom | Suspected Area |
| Engine vibration occurs and engine stops | Air-fuel ratio abnormal |
| Engine stops with no engine vibration | Ignition system, injection stoppage, high load from external parts |
| Engine can be started with accelerator pedal depressed | Insufficient air volume |
| Rough idling after engine started | Air-fuel ratio abnormal, abnormal combustion |

| Vehicle State | Engine Speed | Suspected Area | Primary Parts to Inspect | Procedure | |
| Idling or decelerating | Slowly decreases and engine stalls | Ignition system abnormal | Igniter abnormal |
| 10, 38, 52 |
| Air-fuel ratio abnormal | Air suction |
| 5 to 9 | ||
| Sensor malfunction (value from sensor too lean) |
| 11 to 23 | |||
| Sensor malfunction (value from sensor too rich) | 39 to 51 | ||||
| Fuel supply problem |
| 24 to 37 | |||
| Intake air volume insufficient | Problem with air passage |
| 53 to 55 | ||
| Excessive valve overlap |
| 56 to 59 | |||
| Ignition timing incorrect | Does not operate as expected |
| 60 to 64 | ||
| Rapidly decreases and engine stalls* | Ignition and injection stops (electrical system malfunction) | Power temporarily cut |
| 65, 66 | |
| External part malfunctioning | Increase in load |
| 67 to 69 | ||
| Accelerating | - | Crankshaft position sensor or VVT sensor malfunction | Power temporarily cut |
| 1 |
| Mass air flow meter | Foreign matter adhesion |
| 70 to 73 | ||
| Ignition and injection stops (electrical system malfunction) | Power temporarily cut |
| 74, 75 | ||
| Fuel supply problem | Fuel leak, clog |
| 76 to 80 | ||

| Engine Speed | Suspected Area | Primary Parts to Inspect | Procedure | |
| Slowly decreases and engine stalls | Ignition system abnormal | Igniter abnormal |
| 10, 38, 52 |
| Air-fuel ratio abnormal | Air suction |
| 5 to 9 | |
| Sensor malfunction (value from sensor too lean) |
| 11 to 23 | ||
| Sensor malfunction (value from sensor too rich) | 39 to 51 | |||
| Fuel supply problem |
| 24 to 37 | ||
| Intake air volume insufficient | Problem with air passage |
| 53 to 55 | |
| Excessive valve overlap |
| 56 to 59 | ||
| Ignition timing incorrect | Does not operate as expected |
| 60 to 64 | |
| Rapidly decreases and engine stalls* | Ignition and injection stops (electrical system malfunction) | Power temporarily cut |
| 65, 66 |
| External part malfunctioning | Increase in load |
| 67 to 69 | |
| 1.CHECK FOR ANY OTHER DTCS OUTPUT |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs (Click here).
| Result | Proceed to |
| DTC P1603 and/or P1605 are output | A |
| DTC P1603 or P1605 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 3.CHECK ENGINE IMMOBILISER SYSTEM |
Connect the intelligent tester to the DLC3.
Start the engine.
Idle the engine
Enter the following menus: Powertrain / Engine and ECT / Data List / Immobiliser Communication and Immobiliser Fuel Cut.
Check the Data List indication.
| Data List Item | Result |
| Immobiliser Communication | ON |
| Immobiliser Fuel Cut | OFF |
|
| ||||
| OK | |
| 4.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Problem Symptom | Freeze Frame Data Item | Suspected Area | Proceed to | ||
| Closed Throttle Position SW | Engine Speed | Total of Short FT and Long FT | |||
| When idling or decelerating, engine speed slowly decreases and engine stalls | All 5 sets of freeze frame data are ON | Decreases slowly*1 | All 5 sets of freeze frame data are +15% or more*2 |
| A |
| At least 1 of the 5 sets of freeze frame data is -15% or less*3 | Sensor malfunction (value from sensor too rich) | B | |||
| All 5 sets of freeze frame data are from -15% to +15% |
| C | |||
| When idling or decelerating, engine speed rapidly decreases and engine stalls | Decreases rapidly*1 | - |
| D | |
| When accelerating or driving at constant speed, engine stalls*4 | At least one is OFF | - | - |
| E |

|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 5.CHECK INTAKE SYSTEM |
Check for air leaks in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.].
|
| ||||
| OK | |
| 6.CHECK PURGE VSV |
![]() |
Disconnect the purge hose (on the canister side) of the purge VSV.
Start the engine.
Idle the engine.
Disconnect the connector of the purge VSV.
Check if air flows through the purge VSV.
| *1 | Hose (to Canister) |
| *2 | Purge VSV |
Reconnect the connector of the purge VSV.
Reconnect the purge hose of the purge VSV.
|
| ||||
| OK | |
| 7.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Stop Light Switch | At least 1 of the 5 sets of freeze frame data is ON | Air suction from brake booster | A |
| All 5 sets of freeze frame data are OFF | - | B |
|
| ||||
| A | |
| 8.READ VALUE USING INTELLIGENT TESTER (SHORT FT#1) |
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Start the engine and warm it up until the engine coolant temperature stabilizes.
Idle the engine.
Using the intelligent tester, read Short FT #1 of the Data List while depressing the brake pedal.
|
| ||||
| OK | |
| 9.PERFORM DRIVE TEST |
Connect the intelligent tester to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
Idle the engine.
Using the intelligent tester, read the value of Short FT #1 and Long FT #1 in the Data List.
| Data List | Condition | Specified Condition |
| Short FT #1 + Long FT #1 | The conditions of the vehicle are matched to those present when the problem occurs | -15 to +15% |
|
| ||||
| OK | |
| 10.CHECK IGNITION SYSTEM |
Perform ignition system On-vehicle Inspection (Click here).
|
| ||||
| OK | |
| 11.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Calculate Load | Below 90% of the current value of the vehicle*1 | Mass air flow meter | A |
| AFS Voltage B1S1 | 3.3 V or higher*2 |
| B |
|
| ||||
| A | |
| 12.CHECK MASS AIR FLOW METER |
Remove the mass air flow meter.
Check for foreign matter in the airflow passage of the mass air flow meter.
| Result | Proceed to |
| Visible foreign matter is present | A |
| Visible foreign matter is not present | B |
Reinstall the mass air flow meter.
|
| ||||
| A | |
| 13.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER) |
Check the harnesses and connectors, referring to DTC P0102 inspection procedure .
|
| ||||
| OK | |
| 14.PERFORM DRIVE TEST |
Connect the intelligent tester to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
Idle the engine.
Using the intelligent tester, read the value of Calculate Load in the Data List.
| Data List | Specified Condition |
| Calculate Load | 90 to 110% of the current value of the vehicle |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | ||
| ||
| 15.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
![]() |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the intelligent tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
Change the fuel injection volume using the intelligent tester, and monitor the voltage output of the air fuel ratio and heated oxygen sensors displayed on the intelligent tester.
| Intelligent Tester Display | Specified Condition |
| Control the Injection Volume for A/F Sensor (12.5%) | Air fuel ratio sensor output voltage is below 3.1 V |
| Control the Injection Volume for A/F Sensor (-12.5%) | Air fuel ratio sensor output voltage is higher than 3.4 V |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 16.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR) |
Check the harnesses and connectors, referring to DTC P0171 inspection procedure .
|
| ||||
| OK | |
| 17.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Check the harnesses and connectors, referring to DTC P2237 inspection procedure .
|
| ||||
| OK | |
| 18.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Proceed to |
| Initial Engine Coolant Temp, Initial Intake Air Temp, Ambient Temp for A/C | Difference in temperature between each item is less than 10°C*1 | A |
| Difference in temperature between each item is 10°C or more*2 | B |
|
| ||||
| A | |
| 19.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Initial Engine Coolant Temp, Coolant Temp, Engine Run Time | Range A |
| A |
| Range B | Engine coolant temperature sensor | B | |
| Range C | - | C |
|
| ||||
|
| ||||
| A | |
| 20.INSPECT THERMOSTAT |
Inspect the thermostat (Click here).
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | ||
| ||
| 21.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
| Coolant Temp | 120°C or more | Engine coolant temperature sensor | A |
| Coolant Temp, Ambient Temp for A/C | Engine coolant temperature is lower than outside temperature by 15°C or more | Engine coolant temperature sensor | |
| Both freeze frame data items listed above | Values are other than above | - | B |
|
| ||||
| A | |
| 22.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor (Click here).
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 23.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR) |
Disconnect the ECM connector.
Disconnect the engine coolant temperature sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E11-32 (THW) - W1-2 | Always | Below 1 Ω |
| E11-28 (E2) - W1-1 | Always | Below 1 Ω |
| E11-32 (THW) or W1-2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 24.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| EVAP (Purge) VSV | At least 1 of the 5 sets of freeze frame data is not 0% | Purge VSV | A |
| All 5 sets of freeze frame data are 0% | - | B |
|
| ||||
| A | |
| 25.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL) |
![]() |
Disconnect the purge hose (on the canister side) of the purge VSV.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.
Operate the purge VSV and check the air flow.
| Activate the VSV for Evap Control | Specified Condition |
| ON | Air flows |
| OFF | Air does not flow |
| *1 | Hose (to Canister) |
| *2 | Purge VSV |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 26.INSPECT PURGE VSV |
Inspect the purge VSV (Click here).
|
| ||||
| OK | |
| 27.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV) |
![]() |
Disconnect the purge VSV connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| V3-2 - Body ground | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 28.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM) |
Check the harnesses and connectors, referring to DTC P0443 inspection procedure .
|
| ||||
| OK | |
| 29.CLEAR DTC |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Clear the DTCs (Click here).
| NEXT | |
| 30.READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
Idle the engine for 15 minutes or more.
Using the intelligent tester, read the value of EVAP (Purge) VSV in the Data List.
| Data List | Specified Condition |
| EVAP (Purge) VSV | Value other than 0% is displayed |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 31.PERFORM ACTIVE TEST USING INTELLIGENT TESTER |
![]() |
Disconnect the purge hose (on the canister side) of the purge VSV.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.
Operate the purge VSV and check the airflow.
| Activate the VSV for Evap Control | Specified Condition |
| ON | Air flows |
| OFF | Air does not flow |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 32.CHECK CONNECTOR CONNECTION CONDITION (ECM) |
Check the ECM connector connection condition.
|
| ||||
| OK | ||
| ||
| 33.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for an operating sound from the fuel pump.
| Control the Fuel Pump / Speed | Specified Condition |
| ON | Operating sound heard |
| OFF | Operating sound not heard |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 34.INSPECT FUEL PUMP |
Inspect the fuel pump (Click here).
|
| ||||
| OK | ||
| ||
| 35.CHECK FUEL SYSTEM |
Check the fuel system.
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 36.CHECK FUEL SYSTEM |
Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.
| Result | Proceed to |
| There is foreign matter or signs that fuel pump was stuck | A |
| There is no foreign matter and no signs that fuel pump was stuck | B |
|
| ||||
| A | |
| 37.CHECK FUEL SYSTEM |
Check the fuel system.
|
| ||||
| OK | ||
| ||
| 38.CHECK IGNITION SYSTEM |
Perform ignition system On-vehicle Inspection (Click here).
|
| ||||
| OK | |
| 39.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Calculate Load | 110% or more of the current value of the vehicle*1 | Mass air flow meter | A |
| AFS Voltage B1S1 | Below 3.3 V*2 |
| B |
| Both freeze frame data items listed above | Values are other than above | - | C |
|
| ||||
|
| ||||
| A | |
| 40.CHECK MASS AIR FLOW METER |
Remove the mass air flow meter.
Check for foreign matter in the airflow passage of the mass air flow meter.
| Result | Proceed to |
| Visible foreign matter is not present | A |
| Visible foreign matter is present | B |
|
| ||||
| A | |
| 41.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER) |
Check the harnesses and connectors, referring to DTC P0102 inspection procedure .
|
| ||||
| OK | |
| 42.PERFORM DRIVE TEST |
Connect the intelligent tester to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
Idle the engine.
Using the intelligent tester, read the value of Calculate Load in the Data List.
| Data List | Specified Condition |
| Calculate Load | 90 to 110% of the current value of the vehicle |
|
| ||||
| OK | |
| 43.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
![]() |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the intelligent tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
Change the fuel injection volume using the intelligent tester, and monitor the voltage output of the air fuel ratio and heated oxygen sensors displayed on the intelligent tester.
| Intelligent Tester Display | Specified Condition |
| Control the Injection Volume for A/F Sensor (12.5%) | Air fuel ratio sensor output voltage is below 3.1 V |
| Control the Injection Volume for A/F Sensor (-12.5%) | Air fuel ratio sensor output voltage is higher than 3.4 V |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 44.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR) |
Check the harnesses and connectors, referring to DTC P0171 inspection procedure .
|
| ||||
| OK | |
| 45.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Check the harnesses and connectors, referring to DTC P2237 inspection procedure .
|
| ||||
| OK | |
| 46.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Proceed to |
| Initial Engine Coolant Temp, Initial Intake Air Temp, Ambient Temp for A/C | Difference in temperature between each item is less than 10°C*1 | A |
| Difference in temperature between each item is 10°C or more*2 | B |
|
| ||||
| A | |
| 47.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions present when the DTC was stored which are recorded in the freeze frame data.

| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Initial Engine Coolant Temp, Coolant Temp, Engine Run Time | Range A |
| A |
| Range B | Engine coolant temperature | B | |
| Range C | - | C |
|
| ||||
|
| ||||
| A | |
| 48.INSPECT THERMOSTAT |
Inspect the thermostat (Click here).
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | ||
| ||
| 49.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Coolant Temp | 120°C or higher | Engine coolant temperature sensor | A |
| Coolant Temp, Ambient Temp for A/C | Engine coolant temperature is lower than outside temperature by 15°C or more | Engine coolant temperature sensor | |
| Both freeze frame data items listed above | Values are other than above | - | B |
|
| ||||
| A | |
| 50.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor (Click here).
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 51.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR) |
Disconnect the ECM connector.
Disconnect the engine coolant temperature sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E11-32 (THW) - W1-2 | Always | Below 1 Ω |
| E11-28 (E2) - W1-1 | Always | Below 1 Ω |
| E11-32 (THW) or W1-2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 52.CHECK IGNITION SYSTEM |
Perform ignition system On-vehicle Inspection (Click here).
|
| ||||
| OK | |
| 53.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Total of ISC Learning Value and ISC Feedback Value | Below 80% of the current value of the vehicle | Throttle body | A |
| 80% or more of the current value of the vehicle | B |
|
| ||||
| A | |
| 54.CHECK INTAKE SYSTEM |
Check for air leakage in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.].
|
| ||||
| OK | |
| 55.CHECK INTAKE SYSTEM |
Check the intake system.
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | ||
| ||
| 56.PERFORM ACTIVE TEST USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the intelligent tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank1).
Check the engine speed while operating the camshaft timing oil control valve using the intelligent tester.
| Tester Operation | Specified Condition |
| 0% | Normal engine speed |
| 100% | Engine idles roughly or stalls |
|
| ||||
| OK | |
| 57.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE) |
Performing the Active Test, referring to DTC P0011 inspection procedure .
|
| ||||
| OK | |
| 58.PERFORM ACTIVE TEST USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the intelligent tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank1).
Check the engine speed while operating the camshaft timing oil control valve using the intelligent tester.
| Tester Operation | Specified Condition |
| 0% | Normal engine speed |
| 100% | Engine idles roughly or stalls |
|
| ||||
| OK | |
| 59.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM) |
Disconnect the camshaft timing oil control valve assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E11-13 (OC1+) - C2-2 | Always | Below 1 Ω |
| E11-12 (OC1-) - C2-1 | Always | Below 1 Ω |
| E11-13 (OC1+) or C2-2 - Body ground | Always | 10 kΩ or higher |
| E11-12 (OC1-) or C2-2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 60.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Suspected Area | Proceed to | |
| IGN Advance | Knock Correct Learn Value | ||
| Differs from the current value of the vehicle by 10° or more | Less than 3° |
| A |
| 3° or more | - | B | |
| Differs from the current value of the vehicle by less than 10° | - | - | |
|
| ||||
| A | |
| 61.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor (Click here).
|
| ||||
| OK | |
| 62.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR) |
Disconnect the ECM connector.
Disconnect the engine coolant temperature sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E11-32 (THW) - W1-2 | Always | Below 1 Ω |
| E11-28 (E2) - W1-1 | Always | Below 1 Ω |
| E11-32 (THW) or W1-2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 63.INSPECT MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR) |
Inspect the mass air flow meter (intake air temperature sensor) (Click here).
|
| ||||
| OK | |
| 64.READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
Idle the engine.
Using the intelligent tester, read the value of IGN Advance and Knock Correct Learn Value in the Data List.
| Freeze Frame Data Item for DTC P1605 | Proceed to | |
| IGN Advance | Knock Correct Learn Value | |
| Differs from the current value of the vehicle by 10° or more | Less than 3° | A |
| 3° or more | B | |
| Differs from the current value of the vehicle by less than 10° | - | |
|
| ||||
| A | ||
| ||
| 65.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR) |
Check the harnesses and connectors, referring to DTC P0300 inspection procedure .
|
| ||||
| OK | |
| 66.CHECK IGNITION SYSTEM |
Perform ignition system On-vehicle Inspection (Click here).
|
| ||||
| OK | |
| 67.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Suspected Area | Proceed to | ||
| A/C Signal | Air Conditioner FB Val | Power Steering Signal | ||
| A/C Signal display does not change from OFF*1 | - | Does not change from OFF | - | A |
| Changes from OFF to ON | Power steering system | |||
| A/C Signal display changes from OFF to ON*1 | Value displayed for Air Conditioner FB Val does not increase | Changes from OFF to ON | ||
| Does not change from OFF | - | |||
| Value displayed for Air Conditioner FB Val increases | - | A/C system | B | |
|
| ||||
| A | |
| 68.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Suspected Area | Proceed to | |||
| Electrical Load Signal | Electric Load Feedback Val | Difference between Engine Speed and SPD (NC0) | Vehicle Speed | ||
| Electrical Load Signal display changes from OFF to ON*1, or Value displayed for Electric Load Feedback Val increases*1 | Value displayed for Electric Load Val changes | - | - | Electrical load signal circuit | A |
| Value displayed for Electric Load Val does not change | At least 1 of the 5 sets of freeze frame data is less than 100 rpm | Less than 30 km/h | Automatic transmission system | B | |
| 30 km/h or more | - | C | |||
| All 5 sets of freeze frame data are 100 rpm or more | - | - | C | ||
| Electrical Load Signal display does not change from OFF, or Value displayed for Electric Load Feedback Val does not increase | - | At least 1 of the 5 sets of freeze frame data is less than 100 rpm | Less than 30 km/h | Automatic transmission system | B |
| 30 km/h or more | - | C | |||
| All 5 sets of freeze frame data are 100 rpm or more | - | - | C | ||
|
| ||||
|
| ||||
| A | |
| 69.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Suspected Area | Proceed to | |
| Shift SW Status (R Range) Shift SW Status (2 Range) Shift SW Status (L Range) Shift SW Status (3 Range) | Neutral Position SW Signal | ||
| P and N position are both ON in at least one data set | NSW is ON | Park/neutral position switch | A |
| NSW is OFF | Automatic transmission system | B | |
| All 5 sets of freeze frame data are OFF | NSW is ON | - | C |
| NSW is OFF | Automatic transmission system | B | |
|
| ||||
|
| ||||
| A | ||
| ||
| 70.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Throttle Sensor Position, Calculate Load | Calculate Load decreases while Throttle Sensor Position increases | Mass air flow meter | A |
| Calculate Load does not decrease while Throttle Sensor Position increases | - | B |
|
| ||||
| A | |
| 71.INSPECT MASS AIR FLOW METER |
Remove the mass air flow meter.
Check for foreign matter in the airflow passage of the mass air flow meter.
| Result | Proceed to |
| Visible foreign matter is not present | A |
| Visible foreign matter is present | B |
Install the mass air flow meter.
|
| ||||
| A | |
| 72.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER) |
Check the harnesses and connectors, referring to DTC P0102 inspection procedure .
|
| ||||
| OK | |
| 73.PERFORM DRIVE TEST |
Connect the intelligent tester to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes.
Idle the engine.
Using the intelligent tester, read the value of Calculate Load in the Data List.
| Data List | Specified Condition |
| Calculate Load | 90 to 110% of the current value of the vehicle |
|
| ||||
| OK | |
| 74.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR) |
Check the harnesses and connectors, referring to DTC P0300 inspection procedure .
|
| ||||
| OK | |
| 75.CHECK IGNITION SYSTEM |
Perform ignition system On-vehicle Inspection (Click here).
|
| ||||
| OK | |
| 76.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for an operating sound from the fuel pump.
| Control the Fuel Pump / Speed | Specified Condition |
| ON | Operating sound heard |
| OFF | Operating sound not heard |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 77.INSPECT FUEL PUMP |
Inspect the fuel pump (Click here).
|
| ||||
| OK | ||
| ||
| 78.CHECK FUEL SYSTEM |
Check the fuel system.
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 79.CHECK FUEL SYSTEM |
Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.
| Result | Proceed to |
| There is foreign matter or signs that fuel pump was stuck | A |
| There is no foreign matter and no signs that fuel pump was stuck | B |
|
| ||||
| A | |
| 80.CHECK FUEL SYSTEM |
Check the fuel system.
|
| ||||
| OK | ||
| ||
| 81.CLEAR DTC |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Clear DTCs (Click here).
| NEXT | ||
| ||