Home › ENGINE · 2TR-FBE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2237    Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)

DTC    P2238    Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)

DTC    P2239    Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)

DTC    P2252    Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)

DTC    P2253    Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)

for Preparation Click here


DESCRIPTION

Refer to DTC P2195 .

HINT:
  1. Although the DTC titles refer to the oxygen sensor, these DTCs relate to the air fuel ratio sensor.
  2. Sensor 1 refers to the sensor mounted in front of the three way catalytic converter and located near the engine assembly.


DTC No.
DTC Detection Condition
Trouble Area
P2237
An open in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while the engine is running (2 trip detection logic).
  1. Open or short in air fuel ratio sensor circuit
  2. Air fuel ratio sensor
  3. ECM
P2238
One of the following conditions is met (2 trip detection logic):
  1. The air fuel ratio sensor output drops while the engine is running.
  2. The voltage at terminal A1A+ is 0.5 V or less.
  3. The voltage difference between terminals A1A+ and A1A- is 0.1 V or less.
  1. Open or short in air fuel ratio sensor circuit
  2. Air fuel ratio sensor
  3. ECM
P2239
The A1A+ voltage is higher than 4.5 V (2 trip detection logic).
  1. Open or short in air fuel ratio sensor circuit
  2. Air fuel ratio sensor
  3. ECM
P2252
The A1A- voltage is 0.5 V or less (2 trip detection logic).
  1. Open or short in air fuel ratio sensor circuit
  2. Air fuel ratio sensor
  3. ECM
P2253
A1A- voltage is higher than 4.5 V (2 trip detection logic).
  1. Open or short in air fuel ratio sensor circuit
  2. Air fuel ratio sensor
  3. ECM

WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A5-3 (A1A+) - E22-7 (A1A+)
    Always
    Below 1 Ω
    A5-4 (A1A-) - E22-1 (A1A-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A5-3 (A1A+) or E22-7 (A1A+) - Body ground
    Always
    10 kΩ or higher
    A5-4 (A1A-) or E22-1 (A1A-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.



  1. Reconnect the air fuel ratio sensor connector.


    A227661E07



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
OK


2.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2237, P2238, P2239, P2252 OR P2253)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Switch the ECM from normal mode to check mode (Click here).

  1. Drive the vehicle according to Confirmation Driving Pattern .

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs (Pending DTCs).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P2237, P2238, P2239, P2252 or P2253 is output
    B



B
REPLACE ECM (Click here)
A

END