AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) > TERMINALS OF ECU |
| CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY |

Disconnect the A44 air conditioning amplifier assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A44-1 (GND) - Body ground | L - Body ground | Ground | Always | Below 1 Ω |
| A44-5 (+B1) - A44-1 (GND) | L-Y - L | Battery power source | Always | 11 to 14 V |
| A44-6 (IG+) - A44-1 (GND) | R-L - L | IG power source | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V | |||
| A44-13 (MGC) - Body ground | B - Body ground | Magnet clutch signal | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |||
| A44-14 (HR) - Body ground | L-W - Body ground | No. 1 heater relay signal | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
Reconnect the A44 air conditioning amplifier assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A44-2 (BLW) - Body ground | L-B - Body ground | Blower motor speed control voltage |
| Pulse generation (See waveform 1) |
| A44-3 (AOF) - A44-1 (GND) | Y-B - L | Mode damper servo operation voltage |
| Below 1 V |
| 11 to 14 V | |||
| A44-4 (AOD) - A44-1 (GND) | R-B - L | Mode damper servo operation voltage |
| Below 1 V |
| 11 to 14 V | |||
| A44-7 (ACT) - A44-1 (GND) | R-L - L | Magnet clutch on permit input signal |
| 11 to 14 V |
| Below 1 V | |||
| A44-8 (TW) - A44-1 (GND) | P - L | Engine coolant temperature sensor signal | Ignition switch ON | Pulse generation |
| A44-9 (SPD) - Body ground | V-W - Body ground | Vehicle speed signal | Driving at approximately 20 km/h (12 mph) | Pulse generation (See waveform 2) |
| A44-13 (MGC) - Body ground | B - Body ground | Magnet clutch signal |
| Below 1 V |
| 11 to 14 V | |||
| A44-17 (AMH) - A44-1 (GND) | L - L | Air mix damper servo operation signal |
| 11 to 14 V |
| Below 1 V | |||
| A44-18 (TAMO) - A44-1 (GND) | P - L | Ambient temperature signal | Ignition switch ON | Pulse generation |
| A44-19 (AMC) - A44-1 (GND) | R-W - L | Air mix damper servo operation signal |
| Below 1 V |
| 11 to 14 V | |||
| A44-21 (AC1) - A44-1 (GND) | Y - L | Idle-up request signal |
| 11 to 14 V |
| Below 1 V | |||
| A44-22 (AIR) - A44-1 (GND) | L-W - L | Recirculation damper servo operation voltage |
| Below 1 V |
| 11 to 14 V | |||
| A44-23 (AIF) - A44-1 (GND) | G-Y - L | Recirculation damper servo operation voltage |
| Below 1 V |
| 11 to 14 V | |||
| A43-1 (TE) - A43-14 (SG-4) | G - P | No. 1 cooler thermistor signal |
| 2.0 to 2.4 V |
| 1.4 to 1.8 V | |||
| A43-2 (S5-3) - A44-1 (GND) | W-R - L | Power supply for solar sensor | Ignition switch ON | 4.5 to 5.5 V |
| A43-5 (PSW) - A44-1 (GND) | Y-B - L | Air conditioner pressure sensor signal |
| Below 1 V |
| 11 to 14 V | |||
| A43-7 (TS) - A43-2 (S5-3) | L-W - W-R | Solar sensor signal |
| 0.8 to 4.3 V |
| Below 0.8 V | |||
| A43-9 (VER) - Body ground | R - Body ground | Steering wheel location information signal | Always | Below 1 Ω |
| A43-11 (SG-2) - Body ground | L-Y - Body ground | Ground for pulse position sensor (Mode damper servo) | Always | Below 1 Ω |
| A43-13 (SG-3) - Body ground | BR-Y - Body ground | Ground for cooler thermistor | Always | Below 1 Ω |
| A43-14 (SG-4) - Body ground | P - Body ground | Ground for No. 1 cooler thermistor | Always | Below 1 Ω |
| A43-16 (AGND) - A43-21 (AUXO) | R-L - LG-R | Input signal for pulse position sensor (recirculation damper servo) |
| Pulse generation |
| A43-17 (PIA) - A43-21 (AUXO) | P-B - LG-R | Input signal for pulse position sensor (recirculation damper servo) |
| Pulse generation |
| A43-18 (TR) - A43-13 (SG-3) | GR - BR-Y | Cooler thermistor signal |
| 1.8 to 2.2 V |
| 1.2 to 1.6 V | |||
| A43-20 (SG-1) - Body ground | BR-Y - Body ground | Ground for pulse position sensor (air mix damper servo) | Always | Below 1 V |
| A43-21 (AUXO) - Body ground | LG-R - Body ground | Ground for pulse position sensor (recirculation damper servo) | Always | Below 1 Ω |
| A43-23 (PMB) - A43-20 (SG-1) | W-L - BR-Y | Input signal for pulse position sensor (air mix damper servo) |
| Pulse generation |
| A43-24 (PMA) - A43-20 (SG-1) | W-R - BR-Y | Input signal for pulse position sensor (air mix damper servo) |
| Pulse generation |
| A43-25 (POB) - A43-11 (SG-2) | LG - L-Y | Input signal for pulse position sensor (mode damper servo) |
| Pulse generation |
| A43-26 (POA) - A43-11 (SG-2) | L-O - L-Y | Input signal for pulse position sensor (mode damper servo) |
| Pulse generation |
| A45-3 (PTCR) - A44-1 (GND)* | L-W - L | Idle-up request signal for PTC heater |
| 11 to 14 V |
| Below 1 V | |||
| A44-11 (IGN) - A44-1 (GND)* | B-W - L | Engine speed signal | Engine idling | Pulse generation |
| A45-1 (PTC1) - A44-1 (GND)* | R-W - L | No. 1 PTC heater relay signal |
| 11 to 14 V |
| Below 1 V | |||
| A45-2 (PTC2) - A44-1 (GND)* | GR - L | No. 2 PTC heater relay signal |
| 11 to 14 V |
| Below 1 V | |||
| A45-5 (SWIN) - A44-1 (GND)* | P - L | Heater switch assembly indicator light signal |
| Below 1 V |
| 11 to 14 V | |||
| A45-8 (HEAT) - A44-1 (GND)* | L-O - L | Heater switch assembly input signal |
| Below 1 V |
| 11 to 14 V |
![]() |
Using an oscilloscope, check waveform 1.
| Item | Content |
| Terminal No. (Symbol) | A44-2 (BLW) - Body ground |
| Tool Setting | 1 V/DIV., 50 μsec./DIV. |
| Condition | Ignition switch ON, Blower switch on (LO level) |
![]() |
Using an oscilloscope, check waveform 2.
| Item | Content |
| Terminal No. (Symbol) | A44-9 (SPD) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms./DIV. |
| Condition | Driving at approximately 20 km/h (12 mph) |
| CHECK ECM (for 1KD-FTV [except i-ART]) |

Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E5-18 (AC1) - E6-7 (E1) | Y - BR | Idle-up request signal |
| Below 1 V |
| 11 to 14 V | |||
| E5-19 (ACT) - E6-7 (E1) | R-L - BR | Magnet clutch on permit output signal |
| 11 to 14 V |
| Below 1 V |
| CHECK ECM (for 1KD-FTV [for i-ART]) |

Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E31-10 (AC1) - E28-6 (E1) | Y - BR | Idle-up request signal |
| Below 1 V |
| 11 to 14 V | |||
| E31-13 (ACT) - E28-6 (E1) | R-L - BR | Magnet clutch on permit output signal |
| 11 to 14 V |
| Below 1 V |
| CHECK ECM (for 1GR-FE) |

Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E13-24 (AC1) - E17-1 (E1) | Y - BR | Idle-up request signal |
| Below 1 V |
| 11 to 14 V | |||
| E13-25 (ACT) - E17-1 (E1) | R-L - BR | Magnet clutch on permit output signal |
| 11 to 14 V |
| Below 1 V |
| CHECK ACCESSORY METER ASSEMBLY |

Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A42-3 (TH+) - A42-2 (SG) | W-G - BR-Y | Ambient temperature sensor signal |
| 1.0 to 1.6 V |
| Ambient temperature sensor signal |
| 0.6 to 1.0 V | ||
| A42-9 (DATA) - A42-1 (GND1) | P - LG | Ambient temperature sensor signal | Ignition switch ON | Pulse generation |
| CHECK COMBINATION METER ASSEMBLY |

Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| C26-6 - Body ground | V-R - Body ground | Vehicle speed signal | Driving at approximately 20 km/h (12 mph) | Pulse generation (See waveform) |
![]() |
Using an oscilloscope, check waveform.
| Item | Content |
| Terminal No. (Symbol) | C26-6 - Body ground |
| Tool Setting | 5 V/DIV., 20 ms./DIV. |
| Condition | Driving at approximately 20 km/h (12 mph) |