DTC B1620/21 Driver Side - Side Airbag Sensor Circuit Malfunction |
| DTC Code | Detection Condition | Trouble Area |
| B1620/21 | When both conditions below are met:
|
|

| 1.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and side airbag sensor LH.
|
| ||||
| OK | |
| 2.CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor and side airbag sensor LH.
Check that the connectors (on the center airbag sensor side and side airbag sensor LH side) are not damaged.
|
| ||||
| OK | |
| 3.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - SIDE AIRBAG SENSOR LH) |

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F30-3 (BBL-) - Body ground | Ignition switch ON | Below 1 V |
| F30-4 (BBL+) - Body ground |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Using a service wire, connect terminals 8 (BBD+) and 15 (BBD-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F30-3 (BBL-) - F30-4 (BBL+) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F30-3 (BBL-) - F30-4 (BBL+) | Always | 1 MΩ or higher |
| F30-3 (BBL-) - Body ground | ||
| F30-4 (BBL+) - Body ground |
|
| ||||
| OK | |
| 4.CHECK SIDE AIRBAG SENSOR LH |
![]() |
Interchange the side airbag sensor LH with RH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1620/21 and B1625/22 are not output | A |
| DTC B1625/22 is output | B |
| DTC B1620/21 is output | C |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
| C | |
| 5.CHECK CONNECT |
Check that the connector is properly connected to the rear airbag sensor LH.
|
| ||||
| OK | |
| 6.CHECK CONNECTORS |
Disconnect the connectors from the side airbag sensor LH and rear airbag sensor LH.
Check that the connector (on the rear airbag sensor LH side) is not damaged
|
| ||||
| OK | |
| 7.CHECK REAR AIRBAG SENSOR LH CIRCUIT |

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| R29-2 (BCL+) - Body ground | Ignition Switch ON | Below 1 V |
| R29-1 (BCL-) - Body ground |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Using a service wire, connect terminals 2 (BCL-) and 1 (BCL+) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R29-2 (BCL+) - R29-1 (BCL-) | Always | Below 1 Ω |
Disconnect the service wire from the connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R29-2 (BCL+) - R29-1 (BCL-) | Always | 1 MΩ or higher |
| R29-2 (BCL+) - Body ground | ||
| R29-1 (BCL-) - Body ground |
|
| ||||
| OK | |
| 8.CHECK FOR DTC |
![]() |
Connect the connectors to the side airbag sensor LH.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | |
| 9.CHECK SIDE AIRBAG SENSOR LH |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Interchange the side airbag sensor LH with RH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1625/22 and B1620/21 are not output | A |
| DTC B1620/21 is output | B |
| DTC B1625/22 is output | C |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
| C | ||
| ||