Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1630/23    Driver Side Rear Airbag Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The rear airbag sensor LH consists of the safing sensor, the diagnostic circuit, the lateral deceleration sensor, etc.
If the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether the SRS should be activated.
DTC B1630/23 is recorded when a malfunction is detected in the rear airbag sensor LH circuit.

DTC Code
Detection Condition
Trouble Area
B1630/23
When both conditions below are met:
  1. Rear airbag sensor LH malfunction
  2. Center airbag sensor malfunction
  1. Rear airbag sensor LH
  2. Side airbag sensor LH
  3. Floor wire
  4. Center airbag sensor assembly

WIRING DIAGRAM


C194828E25


INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

1.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connector is properly connected to the rear airbag sensor LH.

    OK:
    The connector is properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


2.CHECK CONNECTORS
  1. Disconnect the connectors from the side airbag sensor LH and rear airbag sensor LH.

  1. Check that the connector (on the rear airbag sensor LH side) is not damaged.

    OK:
    The connector is not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


3.CHECK REAR AIRBAG SENSOR LH CIRCUIT

C194787E21

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    R29-2 (BCL+) - Body ground
    Ignition switch ON
    Below 1 V
    R29-1 (BCL-) - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 2 (BCL-) and 1 (BCL+) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R29-2 (BCL+) - R29-1 (BCL-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R29-2 (BCL+) - R29-1 (BCL-)
    Always
    1 MΩ or higher
    R29-2 (BCL+) - Body ground
    R29-1 (BCL-) - Body ground



NG
REPLACE FLOOR WIRE
OK


4.CHECK FOR DTC


    C167367E08
  1. Connect the connectors to the side airbag sensor LH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1630/23 is output.

HINT:
Codes other than B1630/23 may be output at this time, but they are not related to this check.



NG
REPLACE REAR AIRBAG SENSOR LH
OK


5.CHECK SIDE AIRBAG SENSOR LH
C158841E10
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Interchange the side airbag sensor LH with RH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1635/24 and B1630/23 are not output
    A
    DTC B1630/23 is output
    B
    DTC B1635/24 is output
    C

    HINT:
    Codes other than DTC B1635/24 and B1630/23 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK

B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
C

REPLACE SIDE AIRBAG SENSOR LH