DTC B1635/24 Front Passenger Side Rear Airbag Sensor Circuit Malfunction |
| DTC Code | Detection Condition | Trouble Area |
| B1635/24 | When both conditions below are met:
|
|

| 1.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connector is properly connected to the rear airbag sensor RH.
|
| ||||
| OK | |
| 2.CHECK CONNECTORS |
Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.
Check that the connector (on the rear airbag sensor RH side) is not damaged.
|
| ||||
| OK | |
| 3.CHECK REAR AIRBAG SENSOR RH CIRCUIT |

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| R28-2 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| R28-1 (BCR-) - Body ground |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Using a service wire, connect terminals 1 (BCR+) and 2 (BCR-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R28-2 (BCR+) - R28-1 (BCR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R28-2 (BCR+) - R28-1 (BCR-) | Always | 1 MΩ or higher |
| R28-2 (BCR+) - Body ground | ||
| R28-1 (BCR-) - Body ground |
|
| ||||
| OK | |
| 4.CHECK FOR DTC |
![]() |
Connect the connectors to the side airbag sensor RH.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | |
| 5.CHECK SIDE AIRBAG SENSOR RH |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Interchange the side airbag sensor RH with LH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1635/24 and B1630/23 are not output | A |
| DTC B1635/24 is output | B |
| DTC B1630/23 is output | C |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
| C | ||
| ||