DTC P1264 VN Turbo Controller Malfunction |

| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch to ON for 5 seconds | When communication error occurs between turbo motor and ECM (1 trip detection logic) |
|

| 1.CHECK TURBO MOTOR DRIVER |
![]() |
Disconnect the turbo motor driver connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T32-3 (+B) - T32-4 (GND) | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T32-4 (GND) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Turbo Motor Driver) |
Reconnect the turbo motor driver connector.
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (TURBO MOTOR DRIVER - ECM) |
Disconnect the ECM connector.
Disconnect the turbo motor driver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E7-10 (VNTO) - T32-7 (VNTO) | Always | Below 1 Ω |
| E7-17 (VNTI) - T32-2 (VNTI) | Always | Below 1 Ω |
| E7-10 (VNTO) or T32-7 (VNTO) - Body ground | Always | 10 kΩ or higher |
| E7-17 (VNTI) or T32-2 (VNTI) - Body ground | Always | 10 kΩ or higher |
Reconnect the turbo motor driver connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.INSPECT ECM (VNTO VOLTAGE) |
![]() |
While idling the engine, check the waveform of the ECM connectors using an oscilloscope.
| Tester Connection | Condition | Specified Condition |
| E7-10 (VNTO) - E6-7 (E1) | Idling | Correct waveform is as shown |
| *a | Component with harness connected (ECM) |
|
| ||||
| OK | |
| 4.INSPECT ECM (VNTI VOLTAGE) |
![]() |
While idling the engine, check the waveform of the ECM connectors using an oscilloscope.
| Tester Connection | Condition | Specified Condition |
| E7-17 (VNTI) - E6-7 (E1) | Idling | Correct waveform is as shown |
| *a | Component with harness connected (ECM) |
|
| ||||
| OK | ||
| ||
| 5.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
|
| ||||
| 6.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 7.REPLACE TURBO MOTOR DRIVER |
Replace turbo motor driver (Click here).
| NEXT | |
| 8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs (Click here).
Turn the ignition switch off.
Remove the EFI fuse from the engine room relay block and junction block assembly for more than 1 minute.
Turn the ignition switch to ON and wait for 10 seconds or more.
Start the engine.
Drive the vehicle with a city driving pattern at least 10 minutes.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||