EGR VALVE (w/o Glow Plug Controller) > INSTALLATION |
| 1. INSTALL NO. 2 EGR VALVE ASSEMBLY (w/ EGR Cooler) |
Using a 6 mm hexagon wrench, install the EGR valve adapter, No. 2 EGR valve, EGR cooler, 2 new gaskets, 3 plate washers with the 3 hexagon bolts.
Using a 5 mm hexagon wrench, install the bolt labeled A.

| 2. INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY |
w/ EGR Cooler:
Install a new gasket and electric EGR control valve to the EGR valve adapter with the 2 bolts.

w/o EGR Cooler:
Install a new gasket and the electric EGR control valve.
| 3. INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY (w/o EGR Cooler) |
![]() |
Install 2 new gaskets and the No. 1 EGR pipe with the 2 nuts and 2 bolts.
| 4. TEMPORARILY INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER (w/ EGR Cooler) |
Set a new gasket to the cylinder head.
![]() |
Temporarily install the electric EGR control valve with No. 2 EGR valve and EGR cooler with the 2 nuts and bolt.
Connect the vacuum hose to the No. 2 EGR valve.
Connect the EGR valve position sensor connector.
| 5. INSTALL NO. 2 INTAKE AIR CONNECTOR (w/ EGR Cooler) |
Set a new gasket labeled A to the No. 2 intake air connector as shown in the illustration.
Insert the No. 2 intake air connector with the gasket into the electric EGR control valve.
Install a new gasket labeled B to the electric EGR control valve side shown in the illustration.
| 6. TEMPORARILY INSTALL INTAKE AIR CONNECTOR (w/ EGR Cooler) |
Set a new gasket labeled C to the intake manifold.
Temporarily install the intake air connector to the intake manifold with the 3 bolts.
Temporarily install the intake air connector and electric EGR control valve with the 3 nuts shown in the illustration.

| 7. TIGHTEN NO. 2 INTAKE AIR CONNECTOR AND INTAKE AIR CONNECTOR (w/ EGR Cooler) |
Tighten the 3 nuts labeled A shown in the illustration.
| 8. TIGHTEN INTAKE AIR CONNECTOR AND INTAKE MANIFOLD (w/ EGR Cooler) |
Tighten the 3 bolts labeled B shown in the illustration.
| 9. TIGHTEN EGR COOLER (w/ EGR Cooler) |
Tighten the bolt labeled C shown in the illustration.
Tighten the 2 nuts labeled D shown in the illustration.

| 10. INSTALL INTAKE AIR CONNECTOR (w/o EGR Cooler) |
Install a new gasket and the intake air connector with the bolt and 2 nuts.
| 11. INSTALL NO. 2 INTAKE AIR CONNECTOR BRACKET (w/o EGR Cooler) |
Install the No. 2 intake air connector bracket with the 3 bolts.
| 12. INSTALL NO. 2 INTAKE AIR CONNECTOR BRACKET (w/ EGR Cooler) |
![]() |
Temporarily install the No. 2 intake air connector bracket with the 3 bolts.
Tighten the bolt labeled A.
Tighten the 2 bolts labeled B.
| 13. INSTALL ELECTRIC VACUUM REGULATING VALVE ASSEMBLY |
w/ EGR Cooler:
Install the electric vacuum regulating valve together with the bracket with the 2 bolts.
Connect the 4 vacuum hoses.
Connect the connector.
w/o EGR Cooler:
Install the vacuum switching valve with the screw.
Install the electric vacuum regulating valve together with the bracket with the 2 bolts.
Connect the 3 vacuum hoses.
Connect the 2 connectors.
| 14. INSTALL NO. 1 GAS FILTER WITH GAS FILTER BRACKET (w/ EGR Cooler) |
Install the No. 1 gas filter with gas filter bracket with the bolt.
Connect the 2 vacuum hoses.
| 15. CONNECT NO. 3 WATER BY-PASS PIPE (w/ EGR Cooler) |
Connect the No. 3 water by-pass pipe with wire harness with the 2 bolts.
| 16. INSTALL NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY (w/ EGR Cooler) |
Temporarily install the No. 1, No. 2 and No. 3 injection pipes with the union nuts.
![]() |
w/ EGR Cooler:
Install the No. 2 and No. 3 injection pipe clamps with the 2 bolts and 2 nuts as shown in the illustration.
![]() |
w/o EGR Cooler:
Install the No. 2 and No. 3 injection pipe clamps with the bolt and 2 nuts as shown in the illustration.
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the common rail side.
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.
| 17. CONNECT NO. 4 WATER BY-PASS HOSE (w/ EGR Cooler) |
![]() |
Connect the No. 4 water by-pass hose to the EGR cooler.
| 18. CONNECT NO. 3 WATER BY-PASS HOSE (w/ EGR Cooler) |
Connect the No. 3 water by-pass hose to the EGR cooler.
Install the clamp.
| 19. INSTALL DIESEL THROTTLE BODY ASSEMBLY |
| 20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 21. ADD ENGINE COOLANT (w/ EGR Cooler) |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
![]() |
Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank's B line.
| Item | Specified Condition |
| A/T | 11.1 liters (11.7 US qts, 9.8 Imp. qts) |
| M/T | 9.8 liters (10.4 US qts, 8.6 Imp. qts) |
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
![]() |
Using a wrench, install the vent plug.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2,500 to 3,000 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
After the coolant cools down, check that the coolant level is at the F line.
If the coolant level is below the F line, add TOYOTA SLLC to the F line.
| 22. BLEED AIR FROM FUEL SYSTEM (w/ EGR Cooler) |
![]() |
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.
Start the engine.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs.
Start the engine.*1
![]() |
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.

Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
Clear the DTCs.
Repeat steps *1 to *3.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
| 23. INSPECT FOR COOLANT LEAK (w/ EGR Cooler) |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17.1 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks.
If no external leaks are found, check the cylinder block and head.
| 24. INSPECT FOR FUEL LEAK (w/ EGR Cooler) |
Check that there are no leaks from any part of the fuel system when the engine is stopped. If there is fuel leakage, repair or replace parts as necessary.
Start the engine and check that there are no leaks from any part of the fuel system. If there is fuel leakage, repair or replace parts as necessary.
Disconnect the return hose from the common rail.
Start the engine and check for fuel leaks from the return pipe.
If there is fuel leakage, replace the common rail.
Connect the intelligent tester to the DLC3.
Start the engine and push the intelligent tester main switch on.
Select the Fuel Leak test from the Active Test mode on the intelligent tester.
If the intelligent tester is not available, fully depress the accelerator pedal quickly. Increase the engine speed to the maximum and maintain that speed for 2 seconds. Repeat this operation several times.
Check that there are no leaks from any part of the fuel system.
Reconnect the return hose to the common rail.