Home › TRANSMISSION · A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV with i-ART)

DTC    P0746    Pressure Control Solenoid "A" Performance (Shift Solenoid Valve SL1)

DTC    P0771    Shift Solenoid "E" Performance (Shift Solenoid Valve SR)

for Preparation Click here


DESCRIPTION

The TCM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th or 5th gear).
Then the TCM compares the actual gear with the shift schedule in the TCM memory to detect mechanical problems with the shift solenoid valves, valve body or automatic transmission (clutch, brake, gear, etc.).

DTC Code
DTC Detection Condition
Trouble Area
P0746
The gear required by the TCM does not match the actual gear when driving (2-trip detection logic).
  1. Shift solenoid valve SL1 remains closed
  2. Shift solenoid valve SR remains open or closed
  3. Valve body is blocked
  4. Automatic transmission (clutch, brake, gear, etc.)
P0771
The gear required by the TCM does not match the actual gear when driving (2-trip detection logic).
  1. Shift solenoid valve SR remains open or closed
  2. Shift solenoid valve SL1 remains closed
  3. Valve body is blocked
  4. Automatic transmission (clutch, brake, gear, etc.)

MONITOR DESCRIPTION

These DTCs indicate a stuck ON malfunction or stuck OFF malfunction of shift solenoid valves SR and SL1.
The TCM commands gear shifts by turning the shift solenoid valves ON/OFF. When the gear position commanded by the TCM and the actual gear position are not the same, the TCM illuminates the MIL and stores the DTC.

INSPECTION PROCEDURE


ACTIVE TEST

HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the GTS on.

  6. Enter the following menus: Powertrain / ECT / Active Test.

  7. According to the display on the GTS, perform the Active Test.

    HINT:
    While driving, the shift position can be forcibly changed with the GTS.
    Comparing the shift position commanded by the Active Test with the actual shift position enables you to confirm the problem (Click here).


    ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Shift Position
    Operate shift solenoid valve and set each shift position
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check operation of the shift solenoid valves.
    [Vehicle Condition]
    50 km/h (31 mph) or less

    HINT:
    1. This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.
    2. The 4th to 5th up-shift must be performed with the accelerator pedal released.
    3. The 5th to 4th down-shift must be performed with the accelerator pedal released.
    4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
    5. The shift position commanded by the TCM is shown in the Data List display on the GTS.
    6. Shift solenoid valves SL1 and SR are turned ON/OFF normally when the shift lever is in D.

      TCM gear shift command
      1st
      2nd
      3rd
      4th
      5th
      Shift solenoid valve SL1
      OFF
      OFF
      OFF
      OFF
      ON
      Shift solenoid valve SR
      OFF
      OFF
      OFF
      OFF
      ON

1.CHECK DTC OUTPUT (IN ADDITION TO DTCS P0746 AND P0771)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / ECT / Trouble Codes.

  1. Read the DTCs using the GTS.
    Result 
    Result
    Proceed to
    1. Only P0746 and P0771 are output
    2. Only P0771 is output
    A
    P0746, P0771 and other DTCs are output
    B

    HINT:
    If any other codes besides P0746 and P0771 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART
A


2.PERFORM ACTIVE TEST USING GTS (SHIFT SOLENOID VALVE SLT)

NOTICE:
  1. Perform the test while the ATF temperature is between 50 and 80°C (122 and 176°F).
  2. Be careful to prevent the hose of SST from interfering with the exhaust pipe.
  3. Perform the test with the A/C off.

HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.



    C214323E01
  1. Remove the test plug from the transmission case and connect SST.

SST
09992-00095   (09992-00231, 09992-00271)
  1. Connect the GTS to the DLC3.

  1. Start the engine and warm it up.

  1. Measure the line pressure with SST.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / ECT / Active Test.

  1. According to the display on the GTS, perform the Active Test.

  1. Measure the line pressure.

    ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the Solenoid (SLT)*
    Operate shift solenoid valve SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, TCM commands shift solenoid valve SLT to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling

    HINT:
    *: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Note that the pressure values in the Active Test and hydraulic test are different.

    OK:
    The line pressure changes as specified when performing the Active Test.



NG
REPLACE SHIFT SOLENOID VALVE SLT
OK


3.INSPECT SHIFT SOLENOID VALVE SL1


    C197715E09
  1. Remove shift solenoid valve SL1.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 1
    2. Battery negative (-) → Terminal 2
    Valve moves and makes an operating noise

Text in Illustration 
*a
Component without harness connected
(Shift Solenoid Valve SL1)


NG
REPLACE SHIFT SOLENOID VALVE SL1
OK


4.INSPECT SHIFT SOLENOID VALVE SR


    C214329E01
  1. Remove shift solenoid valve SR.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid valve SR connector terminal - Shift solenoid valve SR body
    20°C (68°F)
    11 to 15 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) → Shift solenoid valve SR connector
    2. Battery negative (-) → Shift solenoid valve SR body
    Valve moves and makes an operating noise

Text in Illustration 
*a
Component without harness connected
(Shift Solenoid Valve SR)


NG
REPLACE SHIFT SOLENOID VALVE SR
OK


5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly (Click here).

    OK:
    There are no foreign objects on any valve.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY