Home › ENGINE ยท 2KD-FTV › FUEL › FUEL INJECTOR

FUEL INJECTOR > REMOVAL

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes and fuel inlet pipe, clean them with a brush and compressed air.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY


    A099256E03
  1. Detach the 4 claws from the pins of the engine cover bracket and remove the No. 1 engine cover sub-assembly.
    Text in Illustration 
    *1
    No. 1 Engine Cover Sub-assembly
    *2
    Claw
    *3
    Pin

  1. Remove the 2 bolts and engine cover bracket.



    A111789
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the vacuum hose from the gas filter.

  1. Loosen the 2 clamps.

  1. Remove the bolt and disconnect the No. 2 air cleaner pipe sub-assembly together with the 2 air hoses.



4. CHECK INJECTOR COMPENSATION CODE

HINT:
If the injector compensation code is not correctly registered, it may cause malfunctions.

  1. Read the injector compensation code .

  1. Check that the compensation code of the installed injector is the same as the code registered in the ECM. If the code is not the same, register the injector compensation code on the injector (Click here).



5. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
  1. After removing the fuel pipe, cover the outlets on the common rail with tape to keep out foreign matter.
  2. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.



    A231803E02
  1. Remove the bolt and No. 2 injection pipe clamp.
    Text in Illustration 
    *1
    No. 2 Injection Pipe Clamp
    *2
    No. 3 Injection Pipe Clamp
    *a
    Injector Side
    *b
    Common Rail Side

  1. Remove the 2 nuts and No. 3 injection pipe clamp.

  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.



6. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection pipe clamp with a new one.



    A098893E01
  1. Remove the 2 bolts and disconnect the 2 injection pipe clamps.



    A231804E02
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
    Text in Illustration 
    *a
    Injector Side
    *b
    Common Rail Side



7. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
  1. Disconnect the 3 fuel hoses.



    A272915E01
  1. Remove the union bolt, 2 bolts, No. 2 nozzle leakage pipe and gasket.
    Text in Illustration 
    *1
    Union Bolt



8. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

NOTICE:
If the cylinder head cover is removed, replace the 4 No. 3 cylinder head cover gaskets with new ones.

  1. Remove the 3 bolts and disconnect the 4 injector connectors.



    A060180E01
  1. Using a small screwdriver, remove the nozzle holder seal by prying between the nozzle holder seal and the cutout part of the cylinder head cover.

  1. Disconnect the ventilation hose.



    G034877E01
  1. Remove the 10 bolts, 2 nuts, cylinder head cover and cylinder head cover gasket.



    A289511
  1. Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.



9. REMOVE INJECTOR ASSEMBLY


    A271617E01
  1. Remove the union bolt, 4 injector hollow screws, 5 gaskets and nozzle leakage pipe.
    Text in Illustration 
    *1
    Union Bolt

    NOTICE:
    1. When removing the nozzle leakage pipe, place a cushion under the pipe.
    2. Be careful not to deform or scratch the union seal surface.
    3. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.



    A271618
  1. Remove the 4 bolts, 4 washers, 4 No. 1 nozzle holder clamps and 4 injectors.

    HINT:
    Arrange the injectors, No. 1 nozzle holder clamps, washers and bolts in the correct order.

  1. Remove the O-ring from each injector.

  1. Remove the 4 injection nozzle seats from the cylinder head.