Home › ENGINE ยท 2KD-FTV › FUEL › COMMON RAIL

COMMON RAIL > REMOVAL

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes and fuel inlet pipe, clean them with a brush and compressed air.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE NO. 1 ENGINE UNDER COVER


4. REMOVE NO. 2 ENGINE UNDER COVER


5. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

  1. Wipe the oil pan and drain plug.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }



6. REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY


    A099256E03
  1. Detach the 4 claws from the pins of the engine cover bracket and remove the No. 1 engine cover sub-assembly.
    Text in Illustration 
    *1
    No. 1 Engine Cover Sub-assembly
    *2
    Claw
    *3
    Pin

  1. Remove the 2 bolts and engine cover bracket.



    A111789
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the vacuum hose from the gas filter.

  1. Loosen the 2 clamps.

  1. Remove the bolt and disconnect the No. 2 air cleaner pipe sub-assembly together with the 2 air hoses.



7. REMOVE MANIFOLD STAY


A099622E01
  1. Remove the 2 bolts and manifold stay.



8. REMOVE OIL FILTER SUB-ASSEMBLY


    A227248E01
  1. Using SST, remove the oil filter.

    SST
    09228-07501  

    HINT:
    Insert the drain hose in the oil filter. Put the disposal container beneath the drain hose to collect the oil from the oil filter.



9. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
  1. After removing the fuel pipe, cover the outlets on the common rail with tape to keep out foreign matter.
  2. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.



    A231803E02
  1. Remove the bolt and No. 2 injection pipe clamp.
    Text in Illustration 
    *1
    No. 2 Injection Pipe Clamp
    *2
    No. 3 Injection Pipe Clamp
    *a
    Injector Side
    *b
    Common Rail Side

  1. Remove the 2 nuts and No. 3 injection pipe clamp.

  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.



10. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection pipe clamp with a new one.



    A098893E01
  1. Remove the 2 bolts and disconnect the 2 injection pipe clamps.



    A231804E02
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
    Text in Illustration 
    *a
    Injector Side
    *b
    Common Rail Side



11. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
  1. Disconnect the 3 fuel hoses.



    A272915E01
  1. Remove the union bolt, 2 bolts, No. 2 nozzle leakage pipe and gasket.
    Text in Illustration 
    *1
    Union Bolt



12. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE


A099624E01
  1. Remove the engine oil level dipstick.

  1. Remove the bolt and injection pipe clamp.

  1. Remove the bolt and engine oil level dipstick guide.

  1. Remove the O-ring from the engine oil level dipstick guide.



13. REMOVE FUEL INLET PIPE SUB-ASSEMBLY


    A098969E11
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.
    Text in Illustration 
    *a
    Common Rail Side
    *b
    Fuel Supply Pump Side



14. REMOVE COMMON RAIL ASSEMBLY

NOTICE:
Do not remove the pressure discharge valve or fuel pressure sensor.

  1. Disconnect the 2 connectors.



    A231856
  1. Remove the 2 bolts and common rail.