DTC B279A Theft Deterrent System Communication Line High Fixation |
| DTC Code | DTC Detection Condition | Trouble Area |
| B279A | The communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck on HI output for 6 seconds or more. |
|


| 1.CLEAR DTC |
Clear the DTCs.
| NEXT | |
| 2.CHECK FOR DTC |
Check for DTCs.
| Result | Proceed to |
| No DTC is output | A |
| DTC B279A and other DTCs are output | B |
| DTC B279A is output | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (SFI OR ECD COMMUNICATION LINE) |
Disconnect the T21 transponder key ECU assembly connector.
Disconnect the E5*1, E9*2 or E25*3 ECM connector.
w/ Blocking System:
Disconnect the T31 telephone transceiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T21-13 (EFIO) - E5-30 (IMI) | Always | Below 1 Ω |
| T21-13 (EFIO) or E5-30 (IMI) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| T21-13 (EFIO) - T31-2 (BLK4) | Always | Below 1 Ω |
| E5-30 (IMI) - T31-8 (BLK3) | Always | Below 1 Ω |
| T21-13 (EFIO) or T31-2 (BLK4) - Body ground | Always | 10 kΩ or higher |
| E5-30 (IMI) or T31-8 (BLK3) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| T21-13 (EFIO) - E9-16 (IMI) | Always | Below 1 Ω |
| T21-13 (EFIO) or E9-16 (IMI) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| T21-13 (EFIO) - T31-2 (BLK4) | Always | Below 1 Ω |
| E9-16 (IMI) - T31-8 (BLK3) | Always | Below 1 Ω |
| T21-13 (EFIO) or T31-2 (BLK4) - Body ground | Always | 10 kΩ or higher |
| E9-16 (IMI) or T31-8 (BLK3) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| T21-13 (EFIO) - E25-31 (IMI) | Always | Below 1 Ω |
| T21-13 (EFIO) or E25-31 (IMI) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| T21-13 (EFIO) - T31-2 (BLK4) | Always | Below 1 Ω |
| E25-31 (IMI) - T31-8 (BLK3) | Always | Below 1 Ω |
| T21-13 (EFIO) or T31-2 (BLK4) - Body ground | Always | 10 kΩ or higher |
| E25-31 (IMI) or T31-8 (BLK3) - Body ground | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T21-13 (EFIO) or E5-30 (IMI) - Body ground | Always | Below 1 V |
| Tester Connection | Condition | Specified Condition |
| T21-13 (EFIO) or T31-2 (BLK4) - Body ground | Always | Below 1 V |
| E5-30 (IMI) or T31-8 (BLK3) - Body ground | Always | Below 1 V |
| Tester Connection | Condition | Specified Condition |
| T21-13 (EFIO) or E9-16 (IMI) - Body ground | Always | Below 1 V |
| Tester Connection | Condition | Specified Condition |
| T21-13 (EFIO) or T31-2 (BLK4) - Body ground | Always | Below 1 V |
| E9-16 (IMI) or T31-8 (BLK3) - Body ground | Always | Below 1 V |
| Tester Connection | Condition | Specified Condition |
| T21-13 (EFIO) or E25-31 (IMI) - Body ground | Always | Below 1 V |
| Tester Connection | Condition | Specified Condition |
| T21-13 (EFIO) or T31-2 (BLK4) - Body ground | Always | Below 1 V |
| E25-31 (IMI) or T31-8 (BLK3) - Body ground | Always | Below 1 V |
|
| ||||
| OK | |
| 4.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO) |
![]() |
Using an oscilloscope, check the waveform.
| Item | Content |
| Tester Connection | T21-13 (EFIO) - T21-16 (GND) |
| Tool Setting | 10V/DIV., 100 ms./DIV. |
| Condition | Ignition switch ON |
| *1 | Waveform |
| *a | Component with harness connected (Transponder Key ECU Assembly) |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - BATTERY AND BODY GROUND) |
![]() |
Disconnect the T21 transponder key ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T21-16 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T21-1 (+B) - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector (to Transponder Key ECU Assembly) |
|
| ||||
| OK | |
| 6.REPLACE ECM |
Temporarily replace the ECM assembly with a new one.
| NEXT | |
| 7.REGISTER ECU COMMUNICATION ID |
Register the ECU - ECM communication ID (Refer to the Service Bulletin).
| NEXT | |
| 8.CLEAR DTC |
Clear the DTCs.
| NEXT | |
| 9.CHECK FOR DTC |
Check for DTCs.
| Result | Proceed to |
| OK | A |
| NG (w/o Blocking System) | B |
| NG (w/ Blocking System) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 10.REPLACE TRANSPONDER KEY ECU ASSEMBLY |
Temporarily replace the transponder key ECU assembly with a new one (Refer to the Service Bulletin).
| NEXT | |
| 11.REGISTER ECU COMMUNICATION ID |
Register the ECU - ECM communication ID (Refer to the Service Bulletin).
| NEXT | |
| 12.CLEAR DTC |
Clear the DTCs.
| NEXT | |
| 13.CHECK FOR DTC |
|
| ||||
| OK | ||
| ||