Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM

DTC    B279A    Theft Deterrent System Communication Line High Fixation

for Preparation Click here


DESCRIPTION

If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck on HI output, the ECM stores this DTC.

DTC Code
DTC Detection Condition
Trouble Area
B279A
The communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck on HI output for 6 seconds or more.
  1. Harness or connector
  2. Transponder key ECU assembly
  3. ECM
  4. Telephone transceiver assembly*
  1. *: w/ Blocking System

WIRING DIAGRAM


B317721E04


B315872E04


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the transponder key ECU assembly, telephone transceiver assembly (w/ Blocking System) or ECM, refer to the Service Bulletin.
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
w/ Blocking System:
  1. When DTC B1586 and B279A are output simultaneously, perform troubleshooting for DTC B279A first.
  2. After troubleshooting for this DTC, make sure B279A is not present. If present, troubleshoot the blocking system DTCs next.

1.CLEAR DTC
  1. Clear the DTCs.


NEXT


2.CHECK FOR DTC
  1. Check for DTCs.
    Result 
    Result
    Proceed to
    No DTC is output
    A
    DTC B279A and other DTCs are output
    B
    DTC B279A is output
    C

    HINT:
    If any DTCs other than B279A are output, troubleshoot those DTCs first.



B
Go to DIAGNOSTIC TROUBLE CODE CHART

C
Go to step 3
A

USE SIMULATION METHOD TO CHECK 

3.CHECK HARNESS AND CONNECTOR (SFI OR ECD COMMUNICATION LINE)
  1. Disconnect the T21 transponder key ECU assembly connector.

  1. Disconnect the E5*1, E9*2, E25*3 or E31*4 ECM connector.

    1. *1: for 1KD-FTV (except i-ART), 2KD-FTV
    2. *2: for 2TR-FE
    3. *3: for 2TR-FBE
    4. *4: for 1KD-FTV (for i-ART)

  1. w/ Blocking System:
    Disconnect the T31 telephone transceiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1KD-FTV (except i-ART), 2KD-FTV [w/o Blocking System]:
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) - E5-30 (IMI)
    Always
    Below 1 Ω
    T21-13 (EFIO) or E5-30 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV (except i-ART), 2KD-FTV [w/ Blocking System]:
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) - T31-2 (BLK4)
    Always
    Below 1 Ω
    E5-30 (IMI) - T31-8 (BLK3)
    Always
    Below 1 Ω
    T21-13 (EFIO) or T31-2 (BLK4) - Body ground
    Always
    10 kΩ or higher
    E5-30 (IMI) or T31-8 (BLK3) - Body ground
    Always
    10 kΩ or higher
    for 2TR-FE (w/o Blocking System):
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) - E9-16 (IMI)
    Always
    Below 1 Ω
    T21-13 (EFIO) or E9-16 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 2TR-FE (w/ Blocking System):
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) - T31-2 (BLK4)
    Always
    Below 1 Ω
    E9-16 (IMI) - T31-8 (BLK3)
    Always
    Below 1 Ω
    T21-13 (EFIO) or T31-2 (BLK4) - Body ground
    Always
    10 kΩ or higher
    E9-16 (IMI) or T31-8 (BLK3) - Body ground
    Always
    10 kΩ or higher
    for 2TR-FBE (w/o Blocking System):
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) - E25-31 (IMI)
    Always
    Below 1 Ω
    T21-13 (EFIO) or E25-31 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 2TR-FBE (w/ Blocking System):
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) - T31-2 (BLK4)
    Always
    Below 1 Ω
    E25-31 (IMI) - T31-8 (BLK3)
    Always
    Below 1 Ω
    T21-13 (EFIO) or T31-2 (BLK4) - Body ground
    Always
    10 kΩ or higher
    E25-31 (IMI) or T31-8 (BLK3) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV (for i-ART) [w/o Blocking System]:
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) - E31-28 (IMI)
    Always
    Below 1 Ω
    T21-13 (EFIO) or E31-28 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV (for i-ART) [w/ Blocking System]:
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) - T31-2 (BLK4)
    Always
    Below 1 Ω
    E31-28 (IMI) - T31-8 (BLK3)
    Always
    Below 1 Ω
    T21-13 (EFIO) or T31-2 (BLK4) - Body ground
    Always
    10 kΩ or higher
    E31-28 (IMI) or T31-8 (BLK3) - Body ground
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for 1KD-FTV (except i-ART), 2KD-FTV [w/o Blocking System]:
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) or E5-30 (IMI) - Body ground
    Always
    Below 1 V
    for 1KD-FTV (except i-ART), 2KD-FTV [w/ Blocking System]:
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) or T31-2 (BLK4) - Body ground
    Always
    Below 1 V
    E5-30 (IMI) or T31-8 (BLK3) - Body ground
    Always
    Below 1 V
    for 2TR-FE (w/o Blocking System):
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) or E9-16 (IMI) - Body ground
    Always
    Below 1 V
    for 2TR-FE (w/ Blocking System):
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) or T31-2 (BLK4) - Body ground
    Always
    Below 1 V
    E9-16 (IMI) or T31-8 (BLK3) - Body ground
    Always
    Below 1 V
    for 2TR-FBE (w/o Blocking System):
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) or E25-31 (IMI) - Body ground
    Always
    Below 1 V
    for 2TR-FBE (w/ Blocking System):
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) or T31-2 (BLK4) - Body ground
    Always
    Below 1 V
    E25-31 (IMI) or T31-8 (BLK3) - Body ground
    Always
    Below 1 V
    for 1KD-FTV (for i-ART) [w/o Blocking System]:
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) or E31-28 (IMI) - Body ground
    Always
    Below 1 V
    for 1KD-FTV (for i-ART) [w/ Blocking System]:
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) or T31-2 (BLK4) - Body ground
    Always
    Below 1 V
    E31-28 (IMI) or T31-8 (BLK3) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)


    B257265E03
  1. Using an oscilloscope, check the waveform.
    Measurement Condition 
    Item
    Content
    Tester Connection
    T21-13 (EFIO) - T21-16 (GND)
    Tool Setting
    10V/DIV., 100 ms./DIV.
    Condition
    Ignition switch ON

    HINT:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

OK:
Waveform is output normally (refer to illustration).

Text in Illustration 
*1
Waveform
*a
Component with harness connected
(Transponder Key ECU Assembly)


NG
Go to step 5
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY 

5.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - BATTERY AND BODY GROUND)


    B242622E07
  1. Disconnect the T21 transponder key ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T21-16 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    T21-1 (+B) - Body ground
    Always
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Transponder Key ECU Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE ECM
  1. Temporarily replace the ECM assembly with a new one.


NEXT


7.REGISTER ECU COMMUNICATION ID
  1. Register the ECU - ECM communication ID (Refer to the Service Bulletin).


NEXT


8.CLEAR DTC
  1. Clear the DTCs.


NEXT


9.CHECK FOR DTC
  1. Check for DTCs.

    OK:
    DTC B279A is not output.

    Result 
    Result
    Proceed to
    OK
    A
    NG (w/o Blocking System)
    B
    NG (w/ Blocking System)
    C



B
REPLACE TRANSPONDER KEY ECU ASSEMBLY

C
Go to step 10
A

END (ECM IS DEFECTIVE) 

10.REPLACE TRANSPONDER KEY ECU ASSEMBLY
  1. Temporarily replace the transponder key ECU assembly with a new one (Refer to the Service Bulletin).


NEXT


11.REGISTER ECU COMMUNICATION ID
  1. Register the ECU - ECM communication ID (Refer to the Service Bulletin).


NEXT


12.CLEAR DTC
  1. Clear the DTCs.


NEXT


13.CHECK FOR DTC
  1. Check for DTCs.

    OK:
    DTC B279A is not output.



NG
REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
OK

END (TRANSPONDER KEY ECU IS DEFECTIVE)