Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM (w/ Secondary Air Injection System)

SFI SYSTEM (w/ Secondary Air Injection System) > Starter Signal Circuit

for Preparation Click here


DESCRIPTION

While the engine is being cranked, current flows from terminal ST2 of the ignition switch through the park/neutral position switch (for A/T) or directly (for M/T) to terminal STA of the ECM (STA signal).

WIRING DIAGRAM


A296813E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
This inspection procedure is based on the premise that the engine can crank normally. If the engine cannot crank normally, proceed to the problem symptoms table (Click here).

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value.

    OK:

    Ignition Switch Position
    Starter Signal
    ON
    Close (Starter signal OFF)
    START
    Open (Starter signal ON)



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE 

2.CHECK STARTER (ST) RELAY (POWER SOURCE)


    A253284E02
  1. Remove the starter (ST) relay from the engine room relay block and junction block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Starter (ST) relay terminal 2 - Body ground
    Engine cranking
    11 to 14 V

    HINT:
    The engine does not crank because the relay is not installed.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Manual Transaxle)
    B
    NG (for Automatic Transaxle)
    C



B
Go to step 5

C
Go to step 7
A


3.INSPECT STARTER (ST) RELAY
  1. Inspect the starter (ST) relay (Click here).



NG
REPLACE STARTER (ST) RELAY
OK


4.CHECK HARNESS AND CONNECTOR (STARTER (ST) RELAY - BODY GROUND)
  1. Remove the starter (ST) relay from the engine room relay block and junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    Starter (ST) relay terminal 1 - Body ground
    Always
    Below 1 Ω


    Result 
    Result
    Proceed to
    OK (for Manual Transaxle)
    A
    OK (for Automatic Transaxle)
    B
    NG
    C



B
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER (ST) RELAY - BODY GROUND)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - IGNITION SWITCH) 

5.CHECK HARNESS AND CONNECTOR (STARTER (ST) RELAY - IGNITION SWITCH)
  1. Remove the starter (ST) relay from the engine room relay block and junction block.

  1. Disconnect the ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    Starter (ST) relay terminal 1 - I8-7 (ST2)
    Always
    Below 1 Ω
    Starter (ST) relay terminal 1 or I8-7 (ST2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER (ST) RELAY - IGNITION SWITCH)
OK


6.INSPECT IGNITION SWITCH ASSEMBLY
  1. Inspect the ignition switch assembly (Click here).



NG
REPLACE IGNITION SWITCH ASSEMBLY
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY) 

7.CHECK HARNESS AND CONNECTOR (STARTER (ST) RELAY - PARK/NEUTRAL POSITION SWITCH)
  1. Remove the starter (ST) relay from the engine room relay block.

  1. Disconnect the park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 1 - N10-5 (L)
    Always
    Below 1 Ω
    ST relay terminal 1 or N10-5 (L) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER (ST) RELAY - PARK/NEUTRAL POSITION SWITCH)
OK


8.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Inspect the park/neutral position switch assembly (Click here).



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
OK


9.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - IGNITION SWITCH)
  1. Disconnect the park/neutral position switch connector.

  1. Disconnect the ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    N10-4 (B) - I8-7 (ST2)
    Always
    Below 1 Ω
    N10-4 (B) or I8-7 (ST2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH - IGNITION SWITCH)
OK


10.INSPECT IGNITION SWITCH ASSEMBLY
  1. Inspect the ignition switch assembly (Click here).



NG
REPLACE IGNITION SWITCH ASSEMBLY
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY)